Hard launches from high horsepower cars at the drag strip require more than just a normal street-style sway bar. BMR Suspensions Xtreme Anti Roll Bar for 1982-2002 GM F-body allows you to launch harder without excessive body roll limiting traction, with little sacrifice to your Camaros street manners. Manufactured from heavy-wall 1.375-inch DOM tubing, BMRs Xtreme Anti Roll Bar (XSB002) is designed to eliminate body roll and transfer as much power as possible to the rear wheels. The XSB002 attaches to your F-body with polyurethane bushings. These bushings are molded from 88-durometer, low-deflection, polyurethane, and are internally fluted to keep grease in the bushing under high compression loads. BMR Suspension designed the XSB002 sway bar for street performance and drag race applications. The large adjustable sway bar has two positions, giving you the versatility to drive to and from the track with the same sway bar. The XSB002 gives you a massive increase in rate over the stock bar (depending on year and model). These rate increases and adjustability allow you to almost eliminate body roll so you can leave the starting line harder with maximum traction. The hollow design gives you loads of strength without adding a lot of weight. When performance is a must, rely on BMR Suspension!BMR Suspensions XSB002 anti roll bar is available in black hammertone and red powdercoat for long-lasting good looks. Installation time is about 1-2 hours. Proudly made in the U.S.A.!Application GuideThis Part Fits: Year Make Model Submodel 1988,1993-2002 Chevrolet Camaro Base 1982-1986 Chevrolet Camaro Berlinetta 1993 Chevrolet Camaro Indianapolis 500 Pace Car 1985-1990 Chevrolet Camaro Iroc-Z 1987 Chevrolet Camaro LT 1989-1992,1996-1997 Chevrolet Camaro RS 1992 Chevrolet Camaro RS Heritage Edition 1982-1987 Chevrolet Camaro Sport 1982-1987,1991-2002 Chevrolet Camaro Z28 1992 Chevrolet Camaro Z28 Heritage Edition 1982 Chevrolet Camaro Z28 Indianapolis 500 Pace Car 1998-2002 Chevrolet Camaro Z28 SS 1982-2002 Pontiac Firebird Base 1989-2002 Pontiac Firebird Formula 1982-1986 Pontiac Firebird S/E 1982-2002 Pontiac Firebird Trans Am 1994 Pontiac Firebird Trans Am GT 1989-1992 Pontiac Firebird Trans Am GTA 1989 Pontiac Firebird Trans Am GTA SE

Hard launches from high horsepower cars at the drag strip require more than just a normal street-style sway bar. BMR Suspensions Xtreme Anti Roll Bar for 1982-2002 GM F-body allows you to launch harder without excessive body roll limiting traction, with little sacrifice to your Camaros street manners. Manufactured from heavy-wall 1.375-inch DOM tubing, BMRs Xtreme Anti Roll Bar (XSB001) is designed to eliminate body roll and transfer as much power as possible to the rear wheels. The XSB001 attaches to your F-body with polyurethane bushings. These bushings are molded from 88-durometer, low-deflection, polyurethane, and are internally fluted to keep grease in the bushing under high compression loads. BMR Suspension designed the XSB001 sway bar for street performance and drag race applications. The large adjustable sway bar has two positions, giving you the versatility to drive to and from the track with the same sway bar. The XSB001 gives you a massive increase in rate over the stock bar (depending on year and model). These rate increases and adjustability allow you to almost eliminate body roll so you can leave the starting line harder with maximum traction. The hollow design gives you loads of strength without adding a lot of weight. When performance is a must, rely on BMR Suspension!BMR Suspensions XSB001 anti roll bar is available in black hammertone and red powdercoat for long-lasting good looks. Installation time is about 1-2 hours. Proudly made in the U.S.A.!Application GuideThis Part Fits: Year Make Model Submodel 1988,1993-2002 Chevrolet Camaro Base 1982-1986 Chevrolet Camaro Berlinetta 1993 Chevrolet Camaro Indianapolis 500 Pace Car 1985-1990 Chevrolet Camaro Iroc-Z 1987 Chevrolet Camaro LT 1989-1992,1996-1997 Chevrolet Camaro RS 1992 Chevrolet Camaro RS Heritage Edition 1982-1987 Chevrolet Camaro Sport 1982-1987,1991-2002 Chevrolet Camaro Z28 1992 Chevrolet Camaro Z28 Heritage Edition 1982 Chevrolet Camaro Z28 Indianapolis 500 Pace Car 1998-2002 Chevrolet Camaro Z28 SS 1982-2002 Pontiac Firebird Base 1989-2002 Pontiac Firebird Formula 1982-1986 Pontiac Firebird S/E 1982-2002 Pontiac Firebird Trans Am 1994 Pontiac Firebird Trans Am GT 1989-1992 Pontiac Firebird Trans Am GTA 1989 Pontiac Firebird Trans Am GTA SE

Hard launches from high horsepower cars at the drag strip require more than just a normal street-style sway bar. BMR Suspensions Xtreme Anti Roll Bar for 1982-2002 GM F-body allows you to launch harder without excessive body roll limiting traction, with little sacrifice to your Camaros street manners. Manufactured from heavy-wall 1.375-inch DOM tubing, BMRs Xtreme Anti Roll Bar (XSB001) is designed to eliminate body roll and transfer as much power as possible to the rear wheels. The XSB001 attaches to your F-body with polyurethane bushings. These bushings are molded from 88-durometer, low-deflection, polyurethane, and are internally fluted to keep grease in the bushing under high compression loads. BMR Suspension designed the XSB001 sway bar for street performance and drag race applications. The large adjustable sway bar has two positions, giving you the versatility to drive to and from the track with the same sway bar. The XSB001 gives you a massive increase in rate over the stock bar (depending on year and model). These rate increases and adjustability allow you to almost eliminate body roll so you can leave the starting line harder with maximum traction. The hollow design gives you loads of strength without adding a lot of weight. When performance is a must, rely on BMR Suspension!BMR Suspensions XSB001 anti roll bar is available in black hammertone and red powdercoat for long-lasting good looks. Installation time is about 1-2 hours. Proudly made in the U.S.A.!Application GuideThis Part Fits: Year Make Model Submodel 1988,1993-2002 Chevrolet Camaro Base 1982-1986 Chevrolet Camaro Berlinetta 1993 Chevrolet Camaro Indianapolis 500 Pace Car 1985-1990 Chevrolet Camaro Iroc-Z 1987 Chevrolet Camaro LT 1989-1992,1996-1997 Chevrolet Camaro RS 1992 Chevrolet Camaro RS Heritage Edition 1982-1987 Chevrolet Camaro Sport 1982-1987,1991-2002 Chevrolet Camaro Z28 1992 Chevrolet Camaro Z28 Heritage Edition 1982 Chevrolet Camaro Z28 Indianapolis 500 Pace Car 1998-2002 Chevrolet Camaro Z28 SS 1982-2002 Pontiac Firebird Base 1989-2002 Pontiac Firebird Formula 1982-1986 Pontiac Firebird S/E 1982-2002 Pontiac Firebird Trans Am 1994 Pontiac Firebird Trans Am GT 1989-1992 Pontiac Firebird Trans Am GTA 1989 Pontiac Firebird Trans Am GTA SE

BMR 82-02 3rd Gen F-Body Xtreme Chrome Moly Lower Control Arms On-Car Adj. (Poly) - Red

BMR 82-02 3rd Gen F-Body Xtreme Chrome Moly Lower Control Arms On-Car Adj. (Poly) - Black Hammertone

BMR 11-14 Ford Mustang / Shelby GT500 Caster Camber Plates - Red

BMR 11- 14 Ford Mustang / Shelby GT500 Caster Camber Plates - Black Hammertone

BMR 90-93 Fox Mustang Caster Camber Plates - Red

BMR 90-93 Fox Mustang Caster Camber Plates - Black Hammertone

Fits 2020-2022 S550 GT500 Mustangs and 2024 Performance pack and Dark horse Mustangs;CNC-machined 6061-T6 billet aluminum;CNC-machined Delrin bushings;Spherical Bearings;All 304 stainless steel rod end spacers;Eliminates vertical link flex;Eliminates bushing deflection;Eliminates wheel alignment changes due to vertical link flex;Designed for street performance, drag race, and road race applications;Durable anodized finish;1-hour installation time;Proudly designed in the U.S.A.;Proudly made in the U.S.A.Application GuideThis Part Fits: Year Make Model Submodel 2024 Ford Mustang Dark Horse 2024 Ford Mustang Dark Horse Premium 2024 Ford Mustang GT 2024 Ford Mustang GT Premium 2020-2022 Ford Mustang Shelby GT500

Stock upper control arms with soft rubber bushings deflect under load and absorb power instead of transferring it to the tires. The factory arms also don't allow for proper camber correction on lowered vehicles. BMR's Delrin, non-adjustable control arms for Mustangs (UTCA064) are CNC-machined from 6061-T6 billet aluminum. This design gives you an incredibly strong control arm that greatly improves performance. Greasable, solid Delrin bushings add a solid, more responsive feel over the stock rubber bushings. The stock control arm bushings deflect under cornering loads giving you inconsistent handling characteristics. BMR's Delrin bushings are designed to eliminate deflection, while being able to stand up to high loads of any performance environment. The UTCA064's heavy-duty construction and solid Delrin bushings give you much improved repeatability on the street, starting line, or in the corners. The UTCA064s are primarily designed for lowered cars that are looking to remove the camber gained from lower than stock ride height vehicles. These are designed longer than factory arms, give you the ability to correct the camber setting on lowered S550s. All lowered cars will benefit from these parts IF you are looking to remove negative camber. For those looking to GAIN negative camber, these are not the correct choice. With a 1.2-inch drop, the most negative camber you can get will be approximately -2.0 degrees. These work very well for drag racers who have lowered ride heights, and are looking for ZERO camber. BMR's heavy-duty spherical bearings are designed to solidly link the spindle to the upper control arm, eliminate deflection and wheel alignment changes. Our spherical bearings will stand up to high loads of any performance environment, offering all of the bind-free suspension articulation needed for great handling. On stock height cars, you cannot exceed -0.50 camber.Application GuideThis Part Fits: Year Make Model Submodel 2019-2020 Ford Mustang Bullitt 2015-2020 Ford Mustang EcoBoost 2015-2020 Ford Mustang EcoBoost Premium 2015-2020 Ford Mustang GT 2015 Ford Mustang GT 50 Years Limited Edition 2015-2020 Ford Mustang GT Premium 2015-2020 Ford Mustang Shelby GT350 2016-2020 Ford Mustang Shelby GT350R 2020 Ford Mustang Shelby GT500 2015-2017 Ford Mustang V6

Launching harder, reducing wheel hop, and adding cornering consistency to your 2016-newer Chevrolet Camaro is easy with upper control arms from BMR Suspension. Stock stamped steel control arms with soft rubber bushings deflect under load and absorb power instead of transferring it to the tires. BMR's rod ended, on-car adjustable control arms for Camaros (UTCA063) are manufactured from heavy-duty 1.25-inch DOM steel tubing with TIG-welded Chrome-moly tube adapters. This design gives you a strong trailing arm that eliminates deflection and greatly improves performance. The UTCA063 features zinc-plated two-piece, X-series, heat-treated, chrome-moly, self-lubricating, Teflon-lined rod ends. It also features 304 stainless steel, custom designed rod end spacers. This design provides reduced deflection, increased articulation, and an all-around improvement in performance. BMR Suspension designed the UTCA063 to work well in street performance, drag race, and road race applications. The stock trailing arms flex under cornering loads giving you inconsistent handling characteristics. Combine this with soft bushings that have massive amounts of deflection and you're left with poor performance. The UTCA063's heavy-duty construction eliminates trailing arm flex, giving you much improved repeatability on the street, starting line, or in the corners. BMR's rod ends allows for fine-tuning and bind-free suspension articulation needed for superior handling at any power level. When performance is a must, rely on BMR Suspension! BMR Suspension's UTCA063 on-car adjustable upper control arms are available in red and black hammertone powdercoat for long-lasting good looks. Installation time is about 1 hour. Proudly made in the U.S.A.Application GuideThis Part Fits: Year Make Model Submodel 2020 Chevrolet Camaro LS 2016-2017,2020 Chevrolet Camaro LT 2020 Chevrolet Camaro LT1 2016-2020 Chevrolet Camaro SS 2017-2020 Chevrolet Camaro ZL1

Launching harder, reducing wheel hop, and adding cornering consistency to your 2016-newer Chevrolet Camaro is easy with upper control arms from BMR Suspension. Stock stamped steel control arms with soft rubber bushings deflect under load and absorb power instead of transferring it to the tires. BMR's rod ended, on-car adjustable control arms for Camaros (UTCA063) are manufactured from heavy-duty 1.25-inch DOM steel tubing with TIG-welded Chrome-moly tube adapters. This design gives you a strong trailing arm that eliminates deflection and greatly improves performance. The UTCA063 features zinc-plated two-piece, X-series, heat-treated, chrome-moly, self-lubricating, Teflon-lined rod ends. It also features 304 stainless steel, custom designed rod end spacers. This design provides reduced deflection, increased articulation, and an all-around improvement in performance. BMR Suspension designed the UTCA063 to work well in street performance, drag race, and road race applications. The stock trailing arms flex under cornering loads giving you inconsistent handling characteristics. Combine this with soft bushings that have massive amounts of deflection and you're left with poor performance. The UTCA063's heavy-duty construction eliminates trailing arm flex, giving you much improved repeatability on the street, starting line, or in the corners. BMR's rod ends allows for fine-tuning and bind-free suspension articulation needed for superior handling at any power level. When performance is a must, rely on BMR Suspension! BMR Suspension's UTCA063 on-car adjustable upper control arms are available in red and black hammertone powdercoat for long-lasting good looks. Installation time is about 1 hour. Proudly made in the U.S.A.Application GuideThis Part Fits: Year Make Model Submodel 2020 Chevrolet Camaro LS 2016-2017,2020 Chevrolet Camaro LT 2020 Chevrolet Camaro LT1 2016-2020 Chevrolet Camaro SS 2017-2020 Chevrolet Camaro ZL1

Launching harder, reducing wheel hop, and adding cornering consistency to your 2016-newer Chevrolet Camaro is easy with upper control arms from BMR Suspension. Stock stamped steel control arms with soft rubber bushings deflect under load and absorb power instead of transferring it to the tires. BMR's rod ended, single-adjustable control arms for Camaros (UTCA062) are manufactured from heavy-duty 1.25-inch DOM steel tubing. The open end is formed from CNC laser cut, CNC formed 3/16-inch steel plate. This design gives you a strong control arm that greatly improves performance. The UTCA062 features zinc-plated two-piece, X-series, heat-treated, chrome-moly, self-lubricating, Teflon-lined rod ends. It also features 304 stainless steel, custom designed rod end spacers. This design provides reduced deflection, increased articulation, and an all-around improvement in performance. BMR Suspension designed the UTCA062 to work well in street performance, drag race, and road race applications. The stock control arms flex under cornering loads giving you inconsistent handling characteristics. Combine this with soft bushings that have massive amounts of deflection and you're left with poor performance. The UTCA062's heavy-duty construction eliminates control arm flex, giving you much improved repeatability on the street, starting line, or in the corners. BMR's rod ends allows for fine-tuning and bind-free suspension articulation needed for superior handling. These are the perfect upgrade for the enthusiast looking to improve performance at an affordable price, while maintaining acceptable NVH levels and ride quality. When performance is a must, rely on BMR Suspension! BMR Suspension's UTCA062 adjustable upper control arms are available in red and black hammertone powdercoat for long-lasting good looks. Installation time is about 2 hour. Proudly made in the U.S.A.Application GuideThis Part Fits: Year Make Model Submodel 2020 Chevrolet Camaro LS 2016-2017,2020 Chevrolet Camaro LT 2020 Chevrolet Camaro LT1 2016-2020 Chevrolet Camaro SS 2017-2020 Chevrolet Camaro ZL1

Launching harder, reducing wheel hop, and adding cornering consistency to your 2016-newer Chevrolet Camaro is easy with upper control arms from BMR Suspension. Stock stamped steel control arms with soft rubber bushings deflect under load and absorb power instead of transferring it to the tires. BMR's rod ended, single-adjustable control arms for Camaros (UTCA062) are manufactured from heavy-duty 1.25-inch DOM steel tubing. The open end is formed from CNC laser cut, CNC formed 3/16-inch steel plate. This design gives you a strong control arm that greatly improves performance. The UTCA062 features zinc-plated two-piece, X-series, heat-treated, chrome-moly, self-lubricating, Teflon-lined rod ends. It also features 304 stainless steel, custom designed rod end spacers. This design provides reduced deflection, increased articulation, and an all-around improvement in performance. BMR Suspension designed the UTCA062 to work well in street performance, drag race, and road race applications. The stock control arms flex under cornering loads giving you inconsistent handling characteristics. Combine this with soft bushings that have massive amounts of deflection and you're left with poor performance. The UTCA062's heavy-duty construction eliminates control arm flex, giving you much improved repeatability on the street, starting line, or in the corners. BMR's rod ends allows for fine-tuning and bind-free suspension articulation needed for superior handling. These are the perfect upgrade for the enthusiast looking to improve performance at an affordable price, while maintaining acceptable NVH levels and ride quality. When performance is a must, rely on BMR Suspension! BMR Suspension's UTCA062 adjustable upper control arms are available in red and black hammertone powdercoat for long-lasting good looks. Installation time is about 2 hour. Proudly made in the U.S.A.Application GuideThis Part Fits: Year Make Model Submodel 2020 Chevrolet Camaro LS 2016-2017,2020 Chevrolet Camaro LT 2020 Chevrolet Camaro LT1 2016-2020 Chevrolet Camaro SS 2017-2020 Chevrolet Camaro ZL1

BMR 78-87 G-Body Upper Control Arms On-Car Adj. w/ Spherical Bearings - Red

BMR 78-87 G-Body Upper Control Arms On-Car Adj. w/ Spherical Bearings - Black Hammertone

Launching harder, reducing wheel hop, and adding cornering consistency to your 1979-2004 Ford Mustang is easy with upper control arms from BMR Suspension. Stock control arms with soft rubber bushings deflect under load and absorb power instead of transferring it to the tires. BMRs polyurethane, on-car adjustable tubular control arms for Mustangs (UTCA015) are manufactured from heavy-duty 1 5/8 inch, 0.120-inch wall DOM steel tubing. The center adjuster is CNC-machined from chrome-moly steel with rolled threads for the ultimate in strength and durability. The arms feature TIG-welded chrome-moly tube adapters. This design gives you a strong control arm that greatly improves performance. Spherical bearings offer the highest levels of strength and articulation. When the highest levels of performance are required, BMR uses heavy-duty Teflon-lines Viking Performance spherical bearings.BMR Suspension designed the UTCA015 to work well in street performance, drag race, and road race applications. The stock control arms flex under even light cornering loads giving you inconsistent handling characteristics. Combine this with soft bushings that have massive amounts of deflection and youre left with poor performance. The UTCA015s heavy-duty construction eliminates control arm flex, giving you much improved repeatability on the street, starting line, or in the corners. BMRs spherical bearings offer tons of articulation for great handling, whiles remaining strong enough to stand up to high loads of any performance environment. These are the perfect upgrade for the enthusiast looking for max performance at an affordable price. When performance is a must, rely on BMR Suspension!BMR Suspensions UTCA015 on-car adjustable spherical upper control arms are available in red and black hammertone powdercoat for long-lasting good looks. Installation time is about 1-2 hours. Proudly made in the U.S.A.This Part Fits: Year Make Model Submodel 1979-1981,1994-2004 Ford Mustang Base 1981 Ford Mustang Cobra 1979-1981 Ford Mustang Ghia 1982-1983 Ford Mustang GL 1982-1983 Ford Mustang GLX 1982-2004 Ford Mustang GT 2001 Ford Mustang GT Bullitt 1984 Ford Mustang GT-350 20th Anniversary 1995 Ford Mustang GTS 1982-1984 Ford Mustang L 1984-1993 Ford Mustang LX 2003-2004 Ford Mustang Mach 1 1984-1986 Ford Mustang SVO 1993-1999,2001,2003-2004 Ford Mustang SVT Cobra 2003 Ford Mustang SVT Cobra 10th Anniversary 1993,1995,2000 Ford Mustang SVT Cobra R 1983 Ford Mustang Turbo GT

Launching harder, reducing wheel hop, and adding cornering consistency to your 1979-2004 Ford Mustang is easy with upper control arms from BMR Suspension. Stock control arms with soft rubber bushings deflect under load and absorb power instead of transferring it to the tires. BMRs polyurethane, on-car adjustable tubular control arms for Mustangs (UTCA015) are manufactured from heavy-duty 1 5/8 inch, 0.120-inch wall DOM steel tubing. The center adjuster is CNC-machined from chrome-moly steel with rolled threads for the ultimate in strength and durability. The arms feature TIG-welded chrome-moly tube adapters. This design gives you a strong control arm that greatly improves performance. Spherical bearings offer the highest levels of strength and articulation. When the highest levels of performance are required, BMR uses heavy-duty Teflon-lines Viking Performance spherical bearings.BMR Suspension designed the UTCA015 to work well in street performance, drag race, and road race applications. The stock control arms flex under even light cornering loads giving you inconsistent handling characteristics. Combine this with soft bushings that have massive amounts of deflection and youre left with poor performance. The UTCA015s heavy-duty construction eliminates control arm flex, giving you much improved repeatability on the street, starting line, or in the corners. BMRs spherical bearings offer tons of articulation for great handling, whiles remaining strong enough to stand up to high loads of any performance environment. These are the perfect upgrade for the enthusiast looking for max performance at an affordable price. When performance is a must, rely on BMR Suspension!BMR Suspensions UTCA015 on-car adjustable spherical upper control arms are available in red and black hammertone powdercoat for long-lasting good looks. Installation time is about 1-2 hours. Proudly made in the U.S.A.This Part Fits: Year Make Model Submodel 1979-1981,1994-2004 Ford Mustang Base 1981 Ford Mustang Cobra 1979-1981 Ford Mustang Ghia 1982-1983 Ford Mustang GL 1982-1983 Ford Mustang GLX 1982-2004 Ford Mustang GT 2001 Ford Mustang GT Bullitt 1984 Ford Mustang GT-350 20th Anniversary 1995 Ford Mustang GTS 1982-1984 Ford Mustang L 1984-1993 Ford Mustang LX 2003-2004 Ford Mustang Mach 1 1984-1986 Ford Mustang SVO 1993-1999,2001,2003-2004 Ford Mustang SVT Cobra 2003 Ford Mustang SVT Cobra 10th Anniversary 1993,1995,2000 Ford Mustang SVT Cobra R 1983 Ford Mustang Turbo GT

The adjustable design allows for fine-tuning of the pinion angle for proper driveline alignment. These are the perfect upgrade for the enthusiast looking to improve performance, while maintaining acceptable NVH levels and ride quality. When performance is a must, rely on BMR Suspension!BMR Suspensions UTCA011 on-car adjustable polyurethane upper control arms are available in red and black hammertone powdercoat for long-lasting good looks. Installation time is about 1-2 hours. Proudly made in the U.S.A.Control arm hardware kit RH002 (includes upper and lower control arm hardware - Highly Recommended) is also available.Application GuideThis Part Fits: Year Make Model Submodel 1965-1967 Buick Gran Sport Base 1964-1967 Buick Skylark Base 1967 Chevrolet Chevelle 300 1967 Chevrolet Chevelle 300 Deluxe 1964-1967 Chevrolet Chevelle Base 1967 Chevrolet Chevelle Concours 1965-1967 Chevrolet Chevelle Deluxe 1964-1967 Chevrolet Chevelle SS 1964-1967 Chevrolet El Camino Base 1964-1967 Chevrolet Malibu Base 1964-1967 Oldsmobile 442 Base 1964-1967 Oldsmobile Cutlass Base 1964-1967 Oldsmobile Cutlass Holiday 1967 Oldsmobile Cutlass Turnpike Cruiser 1964-1967 Pontiac GTO Base 1964-1967 Pontiac LeMans Base

The adjustable design allows for fine-tuning of the pinion angle for proper driveline alignment. These are the perfect upgrade for the enthusiast looking to improve performance, while maintaining acceptable NVH levels and ride quality. When performance is a must, rely on BMR Suspension!BMR Suspensions UTCA011 on-car adjustable polyurethane upper control arms are available in red and black hammertone powdercoat for long-lasting good looks. Installation time is about 1-2 hours. Proudly made in the U.S.A.Control arm hardware kit RH002 (includes upper and lower control arm hardware - Highly Recommended) is also available.Application GuideThis Part Fits: Year Make Model Submodel 1965-1967 Buick Gran Sport Base 1964-1967 Buick Skylark Base 1967 Chevrolet Chevelle 300 1967 Chevrolet Chevelle 300 Deluxe 1964-1967 Chevrolet Chevelle Base 1967 Chevrolet Chevelle Concours 1965-1967 Chevrolet Chevelle Deluxe 1964-1967 Chevrolet Chevelle SS 1964-1967 Chevrolet El Camino Base 1964-1967 Chevrolet Malibu Base 1964-1967 Oldsmobile 442 Base 1964-1967 Oldsmobile Cutlass Base 1964-1967 Oldsmobile Cutlass Holiday 1967 Oldsmobile Cutlass Turnpike Cruiser 1964-1967 Pontiac GTO Base 1964-1967 Pontiac LeMans Base

The adjustable design allows for fine-tuning of the pinion angle for proper driveline alignment. These are the perfect upgrade for the enthusiast looking to improve performance, while maintaining acceptable NVH levels and ride quality. When performance is a must, rely on BMR Suspension!BMR Suspensions UTCA007 on-car adjustable polyurethane upper control arms are available in red and black hammertone powdercoat for long-lasting good looks. Installation time is about 1-2 hours. Proudly made in the U.S.A.Control arm hardware kit RH003 (includes upper and lower control arm hardware - Highly Recommended) is also available.Application GuideThis Part Fits: Year Make Model Submodel 1978-1987 Buick Regal Base 1982-1983 Buick Regal Estate Wagon 1987 Buick Regal GNX 1984-1987 Buick Regal Grand National 1978-1987 Buick Regal Limited 1982 Buick Regal Limited Turbo 1978-1982 Buick Regal Sport 1983-1986 Buick Regal T-Type 1978-1981 Chevrolet Malibu Base 1978-1983 Chevrolet Malibu Classic 1978-1980 Chevrolet Malibu Classic Estate 1978-1981 Chevrolet Malibu Classic Landau 1979-1980 Chevrolet Malibu Classic Sport 1979-1980 Chevrolet Malibu Estate 1979 Chevrolet Malibu Landau 1979 Chevrolet Malibu Police 1979-1980 Chevrolet Malibu Sport 1980 Oldsmobile Cutlass Base 1980-1981 Oldsmobile Cutlass Brougham 1980-1981 Oldsmobile Cutlass LS 1978-1979 Oldsmobile Cutlass Vista Cruiser 1979 Oldsmobile Cutlass Vista Cruiser Brougham 1978-1987 Pontiac Grand Prix Base 1981-1987 Pontiac Grand Prix Brougham 1984-1987 Pontiac Grand Prix LE 1978-1983 Pontiac Grand Prix LJ 1978-1980 Pontiac Grand Prix SJ

The adjustable design allows for fine-tuning of the pinion angle for proper driveline alignment. These are the perfect upgrade for the enthusiast looking to improve performance, while maintaining acceptable NVH levels and ride quality. When performance is a must, rely on BMR Suspension!BMR Suspensions UTCA007 on-car adjustable polyurethane upper control arms are available in red and black hammertone powdercoat for long-lasting good looks. Installation time is about 1-2 hours. Proudly made in the U.S.A.Control arm hardware kit RH003 (includes upper and lower control arm hardware - Highly Recommended) is also available.Application GuideThis Part Fits: Year Make Model Submodel 1978-1987 Buick Regal Base 1982-1983 Buick Regal Estate Wagon 1987 Buick Regal GNX 1984-1987 Buick Regal Grand National 1978-1987 Buick Regal Limited 1982 Buick Regal Limited Turbo 1978-1982 Buick Regal Sport 1983-1986 Buick Regal T-Type 1978-1981 Chevrolet Malibu Base 1978-1983 Chevrolet Malibu Classic 1978-1980 Chevrolet Malibu Classic Estate 1978-1981 Chevrolet Malibu Classic Landau 1979-1980 Chevrolet Malibu Classic Sport 1979-1980 Chevrolet Malibu Estate 1979 Chevrolet Malibu Landau 1979 Chevrolet Malibu Police 1979-1980 Chevrolet Malibu Sport 1980 Oldsmobile Cutlass Base 1980-1981 Oldsmobile Cutlass Brougham 1980-1981 Oldsmobile Cutlass LS 1978-1979 Oldsmobile Cutlass Vista Cruiser 1979 Oldsmobile Cutlass Vista Cruiser Brougham 1978-1987 Pontiac Grand Prix Base 1981-1987 Pontiac Grand Prix Brougham 1984-1987 Pontiac Grand Prix LE 1978-1983 Pontiac Grand Prix LJ 1978-1980 Pontiac Grand Prix SJ

The adjustable design allows for fine-tuning of the pinion angle for proper driveline alignment. These are the perfect upgrade for the enthusiast looking to improve performance, while maintaining acceptable NVH levels and ride quality. When performance is a must, rely on BMR Suspension!BMR Suspensions UTCA005 on-car adjustable polyurethane upper control arms are available in red and black hammertone powdercoat for long-lasting good looks. Installation time is about 1-2 hours. Proudly made in the U.S.A.Control arm hardware kit RH002 (includes upper and lower control arm hardware - Highly Recommended) is also available.Application GuideThis Part Fits: Year Make Model Submodel 1970,1972 Buick Skylark 350 1968-1972 Buick Skylark Base 1968-1972 Buick Skylark Custom 1968 Chevrolet Chevelle 300 1968-1969 Chevrolet Chevelle 300 Deluxe 1968,1970-1972 Chevrolet Chevelle Base 1968-1972 Chevrolet Chevelle Concours 1969-1972 Chevrolet Chevelle Concours Estate 1969-1972 Chevrolet Chevelle Greenbrier 1968-1972 Chevrolet Chevelle Malibu 1968-1972 Chevrolet Chevelle Nomad 1968-1972 Chevrolet Chevelle SS 1968-1972 Chevrolet El Camino Base 1968-1972 Chevrolet El Camino Custom 1968-1972 Chevrolet El Camino SS 1970-1972 Chevrolet Monte Carlo Base 1968-1971 Oldsmobile 442 Base 1968-1972 Oldsmobile Cutlass Base 1972 Oldsmobile Cutlass Cruiser 1968,1971-1972 Oldsmobile Cutlass S 1968-1972 Pontiac GTO Base 1970-1971 Pontiac GTO The Judge 1968-1972 Pontiac LeMans Base 1972 Pontiac LeMans Luxury 1969-1970 Pontiac LeMans Safari 1970-1972 Pontiac LeMans Sport 1971 Pontiac LeMans T37

The adjustable design allows for fine-tuning of the pinion angle for proper driveline alignment. These are the perfect upgrade for the enthusiast looking to improve performance, while maintaining acceptable NVH levels and ride quality. When performance is a must, rely on BMR Suspension!BMR Suspensions UTCA005 on-car adjustable polyurethane upper control arms are available in red and black hammertone powdercoat for long-lasting good looks. Installation time is about 1-2 hours. Proudly made in the U.S.A.Control arm hardware kit RH002 (includes upper and lower control arm hardware - Highly Recommended) is also available.Application GuideThis Part Fits: Year Make Model Submodel 1970,1972 Buick Skylark 350 1968-1972 Buick Skylark Base 1968-1972 Buick Skylark Custom 1968 Chevrolet Chevelle 300 1968-1969 Chevrolet Chevelle 300 Deluxe 1968,1970-1972 Chevrolet Chevelle Base 1968-1972 Chevrolet Chevelle Concours 1969-1972 Chevrolet Chevelle Concours Estate 1969-1972 Chevrolet Chevelle Greenbrier 1968-1972 Chevrolet Chevelle Malibu 1968-1972 Chevrolet Chevelle Nomad 1968-1972 Chevrolet Chevelle SS 1968-1972 Chevrolet El Camino Base 1968-1972 Chevrolet El Camino Custom 1968-1972 Chevrolet El Camino SS 1970-1972 Chevrolet Monte Carlo Base 1968-1971 Oldsmobile 442 Base 1968-1972 Oldsmobile Cutlass Base 1972 Oldsmobile Cutlass Cruiser 1968,1971-1972 Oldsmobile Cutlass S 1968-1972 Pontiac GTO Base 1970-1971 Pontiac GTO The Judge 1968-1972 Pontiac LeMans Base 1972 Pontiac LeMans Luxury 1969-1970 Pontiac LeMans Safari 1970-1972 Pontiac LeMans Sport 1971 Pontiac LeMans T37

Fits 1991-1996 GM B-body;Extended length;On-car adjustable design;CNC-machined chrome-moly center adjuster;High-durometer internally fluted polyurethane greasable bushings;TIG-welded chrome-moly tube adapters;MIG-welded 1 5/8-inch DOM steel tubing;Dramatically reduces control arms flex;Greatly reduces bushing deflection;Improved Performance with OEM-like NVH levels;Designed for street performance, drag race, and road race applications;Durable powdercoat finish;1-2 hour installation time;Proudly designed in the U.S.A.;Proudly made in the U.S.A.Application GuideThis Part Fits: Year Make Model Submodel 1991-1992 Chevrolet Caprice Base 1991-1996 Chevrolet Caprice Classic 1993-1994 Chevrolet Caprice Classic LS 1991-1993 Chevrolet Caprice Classic LTZ 1994-1996 Chevrolet Impala SS

Fits 1991-1996 GM B-body;Extended length;On-car adjustable design;CNC-machined chrome-moly center adjuster;High-durometer internally fluted polyurethane greasable bushings;TIG-welded chrome-moly tube adapters;MIG-welded 1 5/8-inch DOM steel tubing;Dramatically reduces control arms flex;Greatly reduces bushing deflection;Improved Performance with OEM-like NVH levels;Designed for street performance, drag race, and road race applications;Durable powdercoat finish;1-2 hour installation time;Proudly designed in the U.S.A.;Proudly made in the U.S.A.Application GuideThis Part Fits: Year Make Model Submodel 1991-1992 Chevrolet Caprice Base 1991-1996 Chevrolet Caprice Classic 1993-1994 Chevrolet Caprice Classic LS 1991-1993 Chevrolet Caprice Classic LTZ 1994-1996 Chevrolet Impala SS

The adjustable design allows for fine-tuning of the pinion angle for proper driveline alignment. These are the perfect upgrade for the enthusiast looking to improve performance, while maintaining acceptable NVH levels and ride quality. When performance is a must, rely on BMR Suspension!BMR Suspensions UTCA002-1 on-car adjustable polyurethane upper control arms are available in red and black hammertone powdercoat for long-lasting good looks. Installation time is about 1-2 hours. Proudly made in the U.S.A.Control arm hardware kit RH004 (includes upper and lower control arm hardware - Highly Recommended) is also available.Application GuideThis Part Fits: Year Make Model Submodel 1991-1992 Chevrolet Caprice Base 1991-1996 Chevrolet Caprice Classic 1993-1994 Chevrolet Caprice Classic LS 1991-1993 Chevrolet Caprice Classic LTZ 1994-1996 Chevrolet Impala SS

The adjustable design allows for fine-tuning of the pinion angle for proper driveline alignment. These are the perfect upgrade for the enthusiast looking to improve performance, while maintaining acceptable NVH levels and ride quality. When performance is a must, rely on BMR Suspension!BMR Suspensions UTCA002-1 on-car adjustable polyurethane upper control arms are available in red and black hammertone powdercoat for long-lasting good looks. Installation time is about 1-2 hours. Proudly made in the U.S.A.Control arm hardware kit RH004 (includes upper and lower control arm hardware - Highly Recommended) is also available.Application GuideThis Part Fits: Year Make Model Submodel 1991-1992 Chevrolet Caprice Base 1991-1996 Chevrolet Caprice Classic 1993-1994 Chevrolet Caprice Classic LS 1991-1993 Chevrolet Caprice Classic LTZ 1994-1996 Chevrolet Impala SS

Launching harder, reducing wheel hop, and adding cornering consistency to your 2008-2019 Dodge Challenger is easy with upper control arms from BMR Suspension. Stock stamped steel control arms with soft rubber bushings deflect under load and absorb power instead of transferring it to the tires. BMRs rod ended, on-car adjustable control arms for Challengers (UCA112) are manufactured from heavy-duty 1-inch DOM steel tubing with TIG-welded Chrome-moly tube adapters. This design gives you a strong control arm that eliminates deflection and greatly improves performance. The UCA112 features zinc-plated two-piece, X-series, heat-treated, chrome-moly, self-lubricating, Teflon-lined rod ends. It also features 304 stainless steel, custom designed rod end spacers. This design provides reduced deflection, increased articulation, and an all-around improvement in performanceBMR Suspension designed the UCA112 to work well in street performance, drag race, and road race applications. The stock control arms flex under cornering loads giving you inconsistent handling characteristics. Combine this with soft bushings that have massive amounts of deflection and youre left with poor performance. The UCA112s heavy-duty construction eliminates trailing arm flex, giving you much improved repeatability on the street, starting line, or in the corners. BMRs rod ends allows for fine-tuning and bind-free suspension articulation needed for superior handling at any power level. When performance is a must, rely on BMR Suspension!BMR Suspensions UCA112 on-car adjustable upper trailing arms are available in red and black hammertone powdercoat for long-lasting good looks. Installation time is about 2 hours. Proudly made in the U.S.A.Application GuideThis Part Fits: Year Make Model Submodel 2016 Dodge Challenger 392 Hemi Scat Pack Shaker 2017-2020 Dodge Challenger GT 2009-2020 Dodge Challenger R/T 2017-2018 Dodge Challenger R/T 392 2012 Dodge Challenger R/T Classic 2015-2016 Dodge Challenger R/T Plus 2016 Dodge Challenger R/T Plus Shaker 2016,2019-2020 Dodge Challenger R/T Scat Pack 2020 Dodge Challenger R/T Scat Pack Widebody 2016 Dodge Challenger R/T Shaker 2014 Dodge Challenger Rallye Redline 2015 Dodge Challenger Scat Pack 2009-2011 Dodge Challenger SE 2015-2018 Dodge Challenger SRT 392 2018 Dodge Challenger SRT Demon 2015-2020 Dodge Challenger SRT Hellcat 2019-2020 Dodge Challenger SRT Hellcat Redeye 2020 Dodge Challenger SRT Hellcat Redeye Widebody 2020 Dodge Challenger SRT Hellcat Widebody 2008-2014 Dodge Challenger SRT8 2012-2020 Dodge Challenger SXT 2012,2015-2018 Dodge Challenger SXT Plus 2017-2018 Dodge Challenger T/A 2017-2018 Dodge Challenger T/A 392

Launching harder, reducing wheel hop, and adding cornering consistency to your 2008-2019 Dodge Challenger is easy with upper control arms from BMR Suspension. Stock stamped steel control arms with soft rubber bushings deflect under load and absorb power instead of transferring it to the tires. BMRs rod ended, on-car adjustable control arms for Challengers (UCA112) are manufactured from heavy-duty 1-inch DOM steel tubing with TIG-welded Chrome-moly tube adapters. This design gives you a strong control arm that eliminates deflection and greatly improves performance. The UCA112 features zinc-plated two-piece, X-series, heat-treated, chrome-moly, self-lubricating, Teflon-lined rod ends. It also features 304 stainless steel, custom designed rod end spacers. This design provides reduced deflection, increased articulation, and an all-around improvement in performanceBMR Suspension designed the UCA112 to work well in street performance, drag race, and road race applications. The stock control arms flex under cornering loads giving you inconsistent handling characteristics. Combine this with soft bushings that have massive amounts of deflection and youre left with poor performance. The UCA112s heavy-duty construction eliminates trailing arm flex, giving you much improved repeatability on the street, starting line, or in the corners. BMRs rod ends allows for fine-tuning and bind-free suspension articulation needed for superior handling at any power level. When performance is a must, rely on BMR Suspension!BMR Suspensions UCA112 on-car adjustable upper trailing arms are available in red and black hammertone powdercoat for long-lasting good looks. Installation time is about 2 hours. Proudly made in the U.S.A.Application GuideThis Part Fits: Year Make Model Submodel 2016 Dodge Challenger 392 Hemi Scat Pack Shaker 2017-2020 Dodge Challenger GT 2009-2020 Dodge Challenger R/T 2017-2018 Dodge Challenger R/T 392 2012 Dodge Challenger R/T Classic 2015-2016 Dodge Challenger R/T Plus 2016 Dodge Challenger R/T Plus Shaker 2016,2019-2020 Dodge Challenger R/T Scat Pack 2020 Dodge Challenger R/T Scat Pack Widebody 2016 Dodge Challenger R/T Shaker 2014 Dodge Challenger Rallye Redline 2015 Dodge Challenger Scat Pack 2009-2011 Dodge Challenger SE 2015-2018 Dodge Challenger SRT 392 2018 Dodge Challenger SRT Demon 2015-2020 Dodge Challenger SRT Hellcat 2019-2020 Dodge Challenger SRT Hellcat Redeye 2020 Dodge Challenger SRT Hellcat Redeye Widebody 2020 Dodge Challenger SRT Hellcat Widebody 2008-2014 Dodge Challenger SRT8 2012-2020 Dodge Challenger SXT 2012,2015-2018 Dodge Challenger SXT Plus 2017-2018 Dodge Challenger T/A 2017-2018 Dodge Challenger T/A 392

Launching harder, reducing wheel hop, and adding cornering consistency to your 2008-2017 Dodge Challenger is easy with upper control arms from BMR Suspension. Stock stamped steel control arms with soft rubber bushings deflect under load and absorb power instead of transferring it to the tires. BMRs rod ended, single-adjustable trailing arms for Challengers (UCA111) are manufactured from heavy-duty 1-inch DOM steel tubing. The open end is formed from CNC laser cut, CNC formed 3/16-inch steel plate. This design gives you a strong trailing arm that greatly improves performance. The UCA111 features zinc-plated two-piece, X-series, heat-treated, chrome-moly, self-lubricating, Teflon-lined rod ends. It also features 304 stainless steel, custom designed rod end spacers. This design provides reduced deflection, increased articulation, and an all-around improvement in performanceBMR Suspension designed the UCA111 to work well in street performance, drag race, and road race applications. The stock trailing arms flex under cornering loads giving you inconsistent handling characteristics. Combine this with soft bushings that have massive amounts of deflection and youre left with poor performance. The UCA111s heavy-duty construction eliminates trailing arm flex, giving you much improved repeatability on the street, starting line, or in the corners. BMRs rod ends allows for fine-tuning and bind-free suspension articulation needed for superior handling. These are the perfect upgrade for the enthusiast looking to improve performance at an affordable price, while maintaining acceptable NVH levels and ride quality. When performance is a must, rely on BMR Suspension!BMR Suspensions UCA111 adjustable upper control arms are available in black hammertone and red powdercoat for long-lasting good looks. Installation time is about 2 hours. Proudly made in the U.S.A.Application GuideThis Part Fits: Year Make Model Submodel 2016 Dodge Challenger 392 Hemi Scat Pack Shaker 2017-2019 Dodge Challenger GT 2009-2019 Dodge Challenger R/T 2017-2018 Dodge Challenger R/T 392 2012 Dodge Challenger R/T Classic 2015-2016 Dodge Challenger R/T Plus 2016 Dodge Challenger R/T Plus Shaker 2016,2019 Dodge Challenger R/T Scat Pack 2016 Dodge Challenger R/T Shaker 2014 Dodge Challenger Rallye Redline 2015 Dodge Challenger Scat Pack 2009-2011 Dodge Challenger SE 2015-2018 Dodge Challenger SRT 392 2018 Dodge Challenger SRT Demon 2015-2019 Dodge Challenger SRT Hellcat 2019 Dodge Challenger SRT Hellcat Redeye 2008-2014 Dodge Challenger SRT8 2012-2019 Dodge Challenger SXT 2012,2015-2018 Dodge Challenger SXT Plus 2017-2018 Dodge Challenger T/A 2017-2018 Dodge Challenger T/A 392

Launching harder, reducing wheel hop, and adding cornering consistency to your 2008-2017 Dodge Challenger is easy with upper control arms from BMR Suspension. Stock stamped steel control arms with soft rubber bushings deflect under load and absorb power instead of transferring it to the tires. BMRs rod ended, single-adjustable trailing arms for Challengers (UCA111) are manufactured from heavy-duty 1-inch DOM steel tubing. The open end is formed from CNC laser cut, CNC formed 3/16-inch steel plate. This design gives you a strong trailing arm that greatly improves performance. The UCA111 features zinc-plated two-piece, X-series, heat-treated, chrome-moly, self-lubricating, Teflon-lined rod ends. It also features 304 stainless steel, custom designed rod end spacers. This design provides reduced deflection, increased articulation, and an all-around improvement in performanceBMR Suspension designed the UCA111 to work well in street performance, drag race, and road race applications. The stock trailing arms flex under cornering loads giving you inconsistent handling characteristics. Combine this with soft bushings that have massive amounts of deflection and youre left with poor performance. The UCA111s heavy-duty construction eliminates trailing arm flex, giving you much improved repeatability on the street, starting line, or in the corners. BMRs rod ends allows for fine-tuning and bind-free suspension articulation needed for superior handling. These are the perfect upgrade for the enthusiast looking to improve performance at an affordable price, while maintaining acceptable NVH levels and ride quality. When performance is a must, rely on BMR Suspension!BMR Suspensions UCA111 adjustable upper control arms are available in black hammertone and red powdercoat for long-lasting good looks. Installation time is about 2 hours. Proudly made in the U.S.A.Application GuideThis Part Fits: Year Make Model Submodel 2016 Dodge Challenger 392 Hemi Scat Pack Shaker 2017-2020 Dodge Challenger GT 2009-2020 Dodge Challenger R/T 2017-2018 Dodge Challenger R/T 392 2012 Dodge Challenger R/T Classic 2015-2016 Dodge Challenger R/T Plus 2016 Dodge Challenger R/T Plus Shaker 2016,2019-2020 Dodge Challenger R/T Scat Pack 2020 Dodge Challenger R/T Scat Pack Widebody 2016 Dodge Challenger R/T Shaker 2014 Dodge Challenger Rallye Redline 2015 Dodge Challenger Scat Pack 2009-2011 Dodge Challenger SE 2015-2018 Dodge Challenger SRT 392 2018 Dodge Challenger SRT Demon 2015-2020 Dodge Challenger SRT Hellcat 2019-2020 Dodge Challenger SRT Hellcat Redeye 2020 Dodge Challenger SRT Hellcat Redeye Widebody 2020 Dodge Challenger SRT Hellcat Widebody 2008-2014 Dodge Challenger SRT8 2012-2020 Dodge Challenger SXT 2012,2015-2018 Dodge Challenger SXT Plus 2017-2018 Dodge Challenger T/A 2017-2018 Dodge Challenger T/A 392

BMR 67-69 1st Gen F-Body T56 Six Speed Conversion Kit - Red

BMR 67-69 1st Gen F-Body T56 Six Speed Conversion Kit - Black Hammertone

BMR 67-69 1st Gen F-Body Transmission Conversion Crossmember TH350/Powerglide/700R4/4L60E - Red