H&R RSS Coil Overs are designed and tested on the famous Nurburgring, and are for the performance minded driver that requires the mosTUVehicle feedback. The result is flat cornering and supreme directional control-a perfect choice for the high performance driver. RSS Coil Overs lower the center of gravity and reduce body roll for better handling. Like all H&R coil overs, RSS Coil Overs feature H&R exclusive dynamic damper technology and a fully threaded shock body.Installation InstructionsThis Part Fits: Year Make Model Submodel 2005-2010 Ford Mustang Base 2008-2009 Ford Mustang Bullitt 2005-2010 Ford Mustang GT 2007-2008 Ford Mustang Shelby GT 2007-2014 Ford Mustang Shelby GT500 2008-2009 Ford Mustang Shelby GT500KR

H&R RSS Coil Overs are designed and tested on the famous Nurburgring, and are for the performance minded driver that requires the mosTUVehicle feedback. The result is flat cornering and supreme directional control-a perfect choice for the high performance driver. RSS Coil Overs lower the center of gravity and reduce body roll for better handling. Like all H&R coil overs, RSS Coil Overs feature H&R exclusive dynamic damper technology and a fully threaded shock body.Installation InstructionsThis Part Fits: Year Make Model Submodel 2013-2018 Ford Focus ST

H&R RSS Coil Overs are designed and tested on the famous Nurburgring, and are for the performance minded driver that requires the mosTUVehicle feedback. The result is flat cornering and supreme directional control-a perfect choice for the high performance driver. RSS Coil Overs lower the center of gravity and reduce body roll for better handling. Like all H&R coil overs, RSS Coil Overs feature H&R exclusive dynamic damper technology and a fully threaded shock body.Installation InstructionsThis Part Fits: Year Make Model Submodel 2016 Volkswagen Golf Base 2015 Volkswagen Golf Launch Edition 2015-2019 Volkswagen Golf S 2015-2016,2018-2019 Volkswagen Golf SE 2015-2016 Volkswagen Golf SEL 2015 Volkswagen Golf TDI S 2015 Volkswagen Golf TDI SE 2015 Volkswagen Golf TDI SEL 2017 Volkswagen Golf Wolfsburg Edition 2015-2019 Volkswagen GTI Autobahn 2019 Volkswagen GTI Rabbit Edition 2015-2020 Volkswagen GTI S 2015-2020 Volkswagen GTI SE 2017 Volkswagen GTI Sport

H&R RSS Coil Overs are designed and tested on the famous Nurburgring, and are for the performance minded driver that requires the mosTUVehicle feedback. The result is flat cornering and supreme directional control-a perfect choice for the high performance driver. RSS Coil Overs lower the center of gravity and reduce body roll for better handling. Like all H&R coil overs, RSS Coil Overs feature H&R exclusive dynamic damper technology and a fully threaded shock body.Installation InstructionsThis Part Fits: Year Make Model Submodel 2006-2009 Volkswagen GTI Base 2007 Volkswagen GTI Fahrenheit 2006-2007 Volkswagen Jetta 2.0T 2005-2007 Volkswagen Jetta 2.5 2011 Volkswagen Jetta Base 2005 Volkswagen Jetta GL 2005 Volkswagen Jetta GL TDI 2005-2009,2012-2014,2017-2018 Volkswagen Jetta GLI 2015-2016 Volkswagen Jetta GLI SE 2015-2016 Volkswagen Jetta GLI SEL 2005 Volkswagen Jetta GLS 2005 Volkswagen Jetta GLS TDI 2008-2019 Volkswagen Jetta S 2008-2019 Volkswagen Jetta SE 2008-2019 Volkswagen Jetta SEL 2005-2006,2009-2014 Volkswagen Jetta TDI 2010 Volkswagen Jetta TDI Cup Edition 2012-2014 Volkswagen Jetta TDI Premium 2015 Volkswagen Jetta TDI S 2015 Volkswagen Jetta TDI SE 2015 Volkswagen Jetta TDI SEL 2006 Volkswagen Jetta Value Edition 2007-2010 Volkswagen Jetta Wolfsburg Edition 2006-2007 Volkswagen Rabbit 2.5 2008-2009 Volkswagen Rabbit S

H&R 22 VOLKSWAGEN Golf GTI/TSI MK8 RSS Coil Over (22 incl. DCC Requires EBM kit 93068-1)

H&R RSS Coil Overs are designed and tested on the famous Nurburgring, and are for the performance minded driver that requires the mosTUVehicle feedback. The result is flat cornering and supreme directional control-a perfect choice for the high performance driver. RSS Coil Overs lower the center of gravity and reduce body roll for better handling. Like all H&R coil overs, RSS Coil Overs feature H&R exclusive dynamic damper technology and a fully threaded shock body.Installation InstructionsThis Part Fits: Year Make Model Submodel 1998-2005 Volkswagen Golf GL 2004 Volkswagen Golf GL TDI 1999-2005 Volkswagen Golf GLS 2004 Volkswagen Golf GLS TDI 1998-1999 Volkswagen Golf GTI 2002-2005 Volkswagen Golf GTI 1.8T 2003 Volkswagen Golf GTI 20th Anniversary 2002 Volkswagen Golf GTI 337 2000-2001 Volkswagen Golf GTI GLS 2000-2001 Volkswagen Golf GTI GLX 1998,2002-2005 Volkswagen Golf GTI VR6 1998 Volkswagen Golf K2 1999,2005 Volkswagen Golf TDI 1999 Volkswagen Golf Wolfsburg Edition 2005 Volkswagen Jetta 2.5 1998-2005 Volkswagen Jetta GL 2005 Volkswagen Jetta GL TDI 2002-2005 Volkswagen Jetta GLI 1998-2005 Volkswagen Jetta GLS 2005 Volkswagen Jetta GLS TDI 1998-2003 Volkswagen Jetta GLX 1998 Volkswagen Jetta GT 1998 Volkswagen Jetta K2 1998-2005 Volkswagen Jetta TDI 1998-1999,2001,2003 Volkswagen Jetta Wolfsburg Edition

H&R RSS Coil Overs are designed and tested on the famous Nurburgring, and are for the performance minded driver that requires the mosTUVehicle feedback. The result is flat cornering and supreme directional control-a perfect choice for the high performance driver. RSS Coil Overs lower the center of gravity and reduce body roll for better handling. Like all H&R coil overs, RSS Coil Overs feature H&R exclusive dynamic damper technology and a fully threaded shock body.Installation InstructionsThis Part Fits: Year Make Model Submodel 1998-2004 Porsche 911 Carrera

H&R RSS Coil Overs are designed and tested on the famous Nurburgring, and are for the performance minded driver that requires the mosTUVehicle feedback. The result is flat cornering and supreme directional control-a perfect choice for the high performance driver. RSS Coil Overs lower the center of gravity and reduce body roll for better handling. Like all H&R coil overs, RSS Coil Overs feature H&R exclusive dynamic damper technology and a fully threaded shock body.This Part Fits: Year Make Model Submodel 1999-2002 BMW Z3 M Coupe 1998-2002 BMW Z3 M Roadster

H&R RSS Coil Overs are designed and tested on the famous Nurburgring, and are for the performance minded driver that requires the mosTUVehicle feedback. The result is flat cornering and supreme directional control-a perfect choice for the high performance driver. RSS Coil Overs lower the center of gravity and reduce body roll for better handling. Like all H&R coil overs, RSS Coil Overs feature H&R exclusive dynamic damper technology and a fully threaded shock body.Installation InstructionsThis Part Fits: Year Make Model Submodel 1997-1999,2004 Porsche Boxster Base 2000-2003 Porsche Boxster Roadster 2000-2003 Porsche Boxster Roadster S 2004 Porsche Boxster S 2004 Porsche Boxster S Special Edition

H&R RSS Coil Overs are designed and tested on the famous Nurburgring, and are for the performance minded driver that requires the mosTUVehicle feedback. The result is flat cornering and supreme directional control-a perfect choice for the high performance driver. RSS Coil Overs lower the center of gravity and reduce body roll for better handling. Like all H&R coil overs, RSS Coil Overs feature H&R exclusive dynamic damper technology and a fully threaded shock body.Installation InstructionsThis Part Fits: Year Make Model Submodel 1999-2004 Porsche 911 Carrera 4 2002-2004 Porsche 911 Carrera 4S 2001-2005 Porsche 911 Turbo

H&R RSS Coil Overs are designed and tested on the famous Nurburgring, and are for the performance minded driver that requires the mosTUVehicle feedback. The result is flat cornering and supreme directional control-a perfect choice for the high performance driver. RSS Coil Overs lower the center of gravity and reduce body roll for better handling. Like all H&R coil overs, RSS Coil Overs feature H&R exclusive dynamic damper technology and a fully threaded shock body.Installation InstructionsThis Part Fits: Year Make Model Submodel 2008-2014 Mini Cooper S Clubman

H&R RSS Coil Overs are designed and tested on the famous Nurburgring, and are for the performance minded driver that requires the mosTUVehicle feedback. The result is flat cornering and supreme directional control-a perfect choice for the high performance driver. RSS Coil Overs lower the center of gravity and reduce body roll for better handling. Like all H&R coil overs, RSS Coil Overs feature H&R exclusive dynamic damper technology and a fully threaded shock body.Installation InstructionsThis Part Fits: Year Make Model Submodel 2008-2014 Mini Cooper Clubman

H&R RSS Coil Overs are designed and tested on the famous Nurburgring, and are for the performance minded driver that requires the mosTUVehicle feedback. The result is flat cornering and supreme directional control-a perfect choice for the high performance driver. RSS Coil Overs lower the center of gravity and reduce body roll for better handling. Like all H&R coil overs, RSS Coil Overs feature H&R exclusive dynamic damper technology and a fully threaded shock body.Installation InstructionsThis Part Fits: Year Make Model Submodel 2007-2014 Mini Cooper Base 2008-2014 Mini Cooper Clubman 2012-2014 Mini Cooper Coupe 2012-2014 Mini Cooper Coupe John Cooper Works 2012-2014 Mini Cooper Coupe S 2009-2014 Mini Cooper John Cooper Works 2009-2014 Mini Cooper John Cooper Works Clubman 2013 Mini Cooper John Cooper Works GP 2012-2014 Mini Cooper Roadster 2012-2014 Mini Cooper Roadster John Cooper Works 2012-2014 Mini Cooper Roadster S 2007-2014 Mini Cooper S 2008-2014 Mini Cooper S Clubman

H&R RSS Coil Overs are designed and tested on the famous Nurburgring, and are for the performance minded driver that requires the mosTUVehicle feedback. The result is flat cornering and supreme directional control-a perfect choice for the high performance driver. RSS Coil Overs lower the center of gravity and reduce body roll for better handling. Like all H&R coil overs, RSS Coil Overs feature H&R exclusive dynamic damper technology and a fully threaded shock body.Installation InstructionsThis Part Fits: Year Make Model Submodel 2002-2008 Mini Cooper Base 2002-2008 Mini Cooper S

H&R RSS Coil Overs are designed and tested on the famous Nurburgring, and are for the performance minded driver that requires the mosTUVehicle feedback. The result is flat cornering and supreme directional control-a perfect choice for the high performance driver. RSS Coil Overs lower the center of gravity and reduce body roll for better handling. Like all H&R coil overs, RSS Coil Overs feature H&R exclusive dynamic damper technology and a fully threaded shock body.Installation InstructionsThis Part Fits: Year Make Model Submodel 2001-2006 BMW M3 Base

H&R RSS Coil Overs are designed and tested on the famous Nurburgring, and are for the performance minded driver that requires the mosTUVehicle feedback. The result is flat cornering and supreme directional control-a perfect choice for the high performance driver. RSS Coil Overs lower the center of gravity and reduce body roll for better handling. Like all H&R coil overs, RSS Coil Overs feature H&R exclusive dynamic damper technology and a fully threaded shock body.Installation InstructionsThis Part Fits: Year Make Model Submodel 2012-2013 Volkswagen Golf R Base

H&R 20-23 Audi RS6 Avant (AWD) F2 RRS+ Coil Over (Damping Adjustable/RS-Sport Suspension Plus)

H&R RSS+ Coil Overs are the ultimate high performance suspension with features only found on race cars. RSS+ include MONO-TUBE shock design for precise control-and externally adjustable shock damping. Some RSS+ Coil Overs feature high-tech light weight aluminum shock bodies that have a black hard anodized finish for beauty and corrosion resistance-H&R engineers have spared no expense developing RSS+. These beauties feature damping adjustment that simultaneously fine tunes rebound and compression damping for perfect balance and control.Installation InstructionsThis Part Fits: Year Make Model Submodel 2009-2014 Audi A4 Base 2009 Audi A4 Cabriolet 2015-2016 Audi A4 Premium 2015-2016 Audi A4 Premium Plus 2015 Audi A4 Prestige 2009-2012 Audi A4 Quattro Avant 2009-2014 Audi A4 Quattro Base 2009 Audi A4 Quattro Cabriolet 2015-2016 Audi A4 Quattro Premium 2015-2016 Audi A4 Quattro Premium Plus 2015 Audi A4 Quattro Prestige 2010-2014 Audi A5 Cabriolet 2008-2014 Audi A5 Quattro Base 2010-2014 Audi A5 Quattro Cabriolet 2015-2016 Audi A5 Quattro Premium 2015-2016 Audi A5 Quattro Premium Plus 2015 Audi A5 Quattro Prestige 2017 Audi A5 Quattro Sport 2012-2018 Audi A6 Premium 2012-2018 Audi A6 Premium Plus 2018 Audi A6 Sport 2017 Audi A6 Quattro Competition 2012-2015,2017-2020 Audi A6 Quattro Premium 2012-2020 Audi A6 Quattro Premium Plus 2012-2020 Audi A6 Quattro Prestige 2018 Audi A6 Quattro Sport 2014-2016 Audi A6 Quattro TDI Premium Plus 2014-2016 Audi A6 Quattro TDI Prestige 2012-2013 Audi A7 Quattro Base 2017 Audi A7 Quattro Competition 2014-2018 Audi A7 Quattro Premium Plus 2014-2018 Audi A7 Quattro Prestige 2014-2016 Audi A7 Quattro TDI Premium Plus 2014-2016 Audi A7 Quattro TDI Prestige 2013-2015 Audi RS5 Base 2014-2015 Audi RS5 Cabriolet 2010-2013 Audi S4 Base 2009 Audi S4 Cabriolet 2014-2016 Audi S4 Premium Plus 2014-2016 Audi S4 Prestige 2008-2013,2017 Audi S5 Base 2010-2013 Audi S5 Cabriolet 2014-2016 Audi S5 Premium Plus 2014-2016 Audi S5 Prestige

H&R RSS Coil Overs are designed and tested on the famous Nurburgring, and are for the performance minded driver that requires the mosTUVehicle feedback. The result is flat cornering and supreme directional control-a perfect choice for the high performance driver. RSS Coil Overs lower the center of gravity and reduce body roll for better handling. Like all H&R coil overs, RSS Coil Overs feature H&R exclusive dynamic damper technology and a fully threaded shock body.Installation InstructionsThis Part Fits: Year Make Model Submodel 2004 Volkswagen Golf GL 2004 Volkswagen Golf GL TDI 2004 Volkswagen Golf GLS 2004 Volkswagen Golf GLS TDI 2004 Volkswagen Golf GTI 1.8T 2004 Volkswagen Golf GTI VR6 2004 Volkswagen R32 Base

H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.

H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.

H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.

H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.

H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.

H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.

H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.

H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.

H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.

H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.

H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.

H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.

H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.

H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.

H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.

H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.

H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.