All

The CVT Transmission in the 2015-2021 Subaru WRX is an impressive system, providing smooth and seamless gear changes with the pull of a lever. However, overheating the transmission fluid can cause early component failure, especially for those interested in racing their WRX or even towing a small trailer. Mishimoto has just the solution for any high-stress situation you can throw to your CVT-equipped WRX. Mishimoto'started by placing a large 19-row oil cooler in the front of the vehicle, where it gets the most amount of airflow. The Mishimoto oil cooler kit is designed to work with the stock transmission cooler, creating a system that is ready for any challenge. When installed, the Mishimoto engineers put the transmission cooler through a series of rigorous tests, including driving the vehicle, fully-loaded with occupants and supplier, up a steep grade to measure the efficiency of the 19-row oil cooler. Mishimoto engineers saw consistent 20 Degrees Fahrenheit (6.7 Degrees Celsius) drops in transmission fluid temperatures, with temperature decreases even during normal driving. If you drive your CVT WRX hard on the racetrack or street, the Mishimoto CVT Transmission cooler is a must! Direct fit for 2015-2021 Subaru WRX w/ stock turbo Insulates turbo hot side to reduce engine bay temperatures and maintain turbocharger efficiency Protects vital cooling components from excessive heat Interior layer is rated to withstand 2,300°F Volcanic lava rock and titanium outer layer with high-silica and stainless-steel inner layer for optimal heat protection Stainless-steel fastening buttons resist corrosion Includes stainless-steel wire and springs for multiple installation options Mishimoto Lifetime Warranty Attributes: GTIN: 00748354015157 Brand Name: Mishimoto TechSpec Rows: 19 TechSpec Core Construction: N/A TechSpec Core Length (in): 11 TechSpec Core Height (in): 5.43 TechSpec Core Thickness (in): 1.97 TechSpec Engine Codes: FA20DIT TechSpec Chassis Codes: VA TechSpec Installation Notes: 22 in-lbs recommended for all worm-gear clamps.--These clamps have an operating range of 18-27 in- 2-3NM.--Do not exceed the maximum torque rating of 27 in-lbs----Recommended torque specification for all straight fittings and banjo bolts: 15-25 lb-ftDo not exceed the maximum torque rating of 35 ft-lb TechSpec Caution: It is the installer's responsibility to check all thermostat plugs, NPT plugs, line fittings, and other connections to assure they are fully tightened before operating the vehicle. Mishimoto recommends that you check all connections at regular intervals, especially during the first few miles after installation. For additional technical information, contact our customer experience team. TechSpec Overall Height (in): N/A TechSpec Overall Length (in): N/A TechSpec Overall Width (in): N/A TechSpec Inlet: N/A TechSpec Outlet: N/A TechSpec Includes: Application-Specific Mounting Brackets--19-Row Oil Cooler--6-ft Rubber Transmission Hose, 3/8-in I.D.--45 -10AN to 3/8-in Barbed Push-On Fittings--Worm-Gear Clamps--Mounting Hardware Set--Mishimoto Lifetime Warranty TechSpec Applications: 2015-2021 Subaru WRX TechSpec Fluid Capacity (qts): N/A TechSpec Note: This will add approximately 1 qt. of CVT transmission fluid. The transmission fluid is called ñHT CVT Fluid" and it can be purchased at any Subaru dealer.--Recommended torque specification for all straight fittings and banjo bolts: 15-25 lb-ftDo not exceed the maximum torque rating of 35 ft-lb SellingPoint01: 20 F (6.7 C) temperature decrease compared to using only the stock transmission cooler SellingPoint02: Direct fit with no cutting or modification to the vehicle SellingPoint03: 19-row stacked-plate oil cooler is front mounted for maximum airflow SellingPoint04: Mounting brackets include provisions for aftermarket horns SellingPoint05: Works in conjunction with the stock transmission cooler SellingPoint06: Works with the Mishimoto engine oil cooler kit SellingPoint07: Cooler available in Sleek Silver or Stealth Black SellingPoint08: Adds approximately 1 qt of transmission fluid SellingPoint09: Mishimoto Lifetime Warranty SellingPoint10: N/A SellingPoint11: N/A SellingPoint12: N/A SellingPoint13: N/A SellingPoint14: N/A SellingPoint15: N/A Install Difficulty: 3 OptionLabel: Black Extended Information: Country of Origin: China Life Cycle Status: Available To Order Packing Information: Quantity of Each: 1 Package UOM: EA Dimension: 17.8 x 7.9 x 14.15 inches Weight: 9.3 lb

The CVT Transmission in the 2015-2021 Subaru WRX is an impressive system, providing smooth and seamless gear changes with the pull of a lever. However, overheating the transmission fluid can cause early component failure, especially for those interested in racing their WRX or even towing a small trailer. Mishimoto has just the solution for any high-stress situation you can throw to your CVT-equipped WRX. Mishimoto'started by placing a large 19-row oil cooler in the front of the vehicle, where it gets the most amount of airflow. The Mishimoto oil cooler kit is designed to work with the stock transmission cooler, creating a system that is ready for any challenge. When installed, the Mishimoto engineers put the transmission cooler through a series of rigorous tests, including driving the vehicle, fully-loaded with occupants and supplier, up a steep grade to measure the efficiency of the 19-row oil cooler. Mishimoto engineers saw consistent 20 Degrees Fahrenheit (6.7 Degrees Celsius) drops in transmission fluid temperatures, with temperature decreases even during normal driving. If you drive your CVT WRX hard on the racetrack or street, the Mishimoto CVT Transmission cooler is a must! Direct fit for 2015-2021 Subaru WRX w/ stock turbo Insulates turbo hot side to reduce engine bay temperatures and maintain turbocharger efficiency Protects vital cooling components from excessive heat Interior layer is rated to withstand 2,300°F Volcanic lava rock and titanium outer layer with high-silica and stainless-steel inner layer for optimal heat protection Stainless-steel fastening buttons resist corrosion Includes stainless-steel wire and springs for multiple installation options Mishimoto Lifetime Warranty Attributes: GTIN: 00748354015140 Brand Name: Mishimoto TechSpec Rows: 19 TechSpec Core Construction: N/A TechSpec Core Length (in): 11 TechSpec Core Height (in): 5.43 TechSpec Core Thickness (in): 1.97 TechSpec Engine Codes: FA20DIT TechSpec Chassis Codes: VA TechSpec Installation Notes: 22 in-lbs recommended for all worm-gear clamps.--These clamps have an operating range of 18-27 in- 2-3NM.--Do not exceed the maximum torque rating of 27 in-lbs----Recommended torque specification for all straight fittings and banjo bolts: 15-25 lb-ftDo not exceed the maximum torque rating of 35 ft-lb TechSpec Caution: It is the installer's responsibility to check all thermostat plugs, NPT plugs, line fittings, and other connections to assure they are fully tightened before operating the vehicle. Mishimoto recommends that you check all connections at regular intervals, especially during the first few miles after installation. For additional technical information, contact our customer experience team. TechSpec Overall Height (in): N/A TechSpec Overall Length (in): N/A TechSpec Overall Width (in): N/A TechSpec Inlet: N/A TechSpec Outlet: N/A TechSpec Includes: Application-Specific Mounting Brackets--19-Row Oil Cooler--6-ft Rubber Transmission Hose, 3/8-in I.D.--45 -10AN to 3/8-in Barbed Push-On Fittings--Worm-Gear Clamps--Mounting Hardware Set--Mishimoto Lifetime Warranty TechSpec Applications: 2015-2021 Subaru WRX TechSpec Fluid Capacity (qts): N/A TechSpec Note: This will add approximately 1 qt. of CVT transmission fluid. The transmission fluid is called ñHT CVT Fluid" and it can be purchased at any Subaru dealer.--Recommended torque specification for all straight fittings and banjo bolts: 15-25 lb-ftDo not exceed the maximum torque rating of 35 ft-lb SellingPoint01: 20 F (6.7 C) temperature decrease compared to using only the stock transmission cooler SellingPoint02: Direct fit with no cutting or modification to the vehicle SellingPoint03: 19-row stacked-plate oil cooler is front mounted for maximum airflow SellingPoint04: Mounting brackets include provisions for aftermarket horns SellingPoint05: Works in conjunction with the stock transmission cooler SellingPoint06: Works with the Mishimoto engine oil cooler kit SellingPoint07: Cooler available in Sleek Silver or Stealth Black SellingPoint08: Adds approximately 1 qt of transmission fluid SellingPoint09: Mishimoto Lifetime Warranty SellingPoint10: N/A SellingPoint11: N/A SellingPoint12: N/A SellingPoint13: N/A SellingPoint14: N/A SellingPoint15: N/A Install Difficulty: 3 OptionLabel: Silver Extended Information: Country of Origin: China Life Cycle Status: Available To Order Packing Information: Quantity of Each: 1 Package UOM: EA Dimension: 17.8 x 7.9 x 14.15 inches Weight: 9.3 lb

The transmission is the backbone of your Grand Cherokee. It's responsible for transmitting large quantities of torque from your V8 or 3.0L EcoDiesel powerplant. That much torque generates a lot of heat, and if that heat isn't dissipated, it can destroy your transmission. The transmission cooler does a good job of keeping trans fluid temperatures in check, but only if the fluid can reach it. The stock cooling system of the 8HP transmission utilizes an in-line thermal bypass valve that controls fluid flow to the transmission cooler. The purpose of this valve is to prevent transmission fluid from flowing to the cooler until it reaches operating temperature. The thermostat inside this valve is prone to failure, however, and when that happens, the fluid never flows to the cooler, and the transmission can overheat. That's why Mishimoto has developed a thermal bypass valve upgrade for your 2016-2020 Jeep Grand Cherokee. Our CNC-machined aluminum thermal bypass valve not only looks better than the stock unit, but it performs better too. This Mishimoto thermal bypass valve kit includes a fully serviceable thermostat for fast warm-up in cold climates. This kit also includes a thermostat bypass that can be installed to provide constant cooling in warm climates or for use in extreme driving/towing conditions. The Mishimoto thermal bypass valve features strategically machined internal passages, providing improved flow over the stock valve for more effective cooling. In addition, cooling fins machined into the valve body add even more heat dissipation. This 2016-2020 Jeep Grand Cherokee Thermal Bypass Full-Flow Valve Kit is built to last a lifetime with a durable black anodized finish and our Mishimoto Lifetime Warranty. Direct fit for 2016-2020 Jeep Grand Cherokee 3.0L/5.7L/6.4L Installs in less than 1 hour Eliminates failure-prone bypass valve Durable CNC-machined billet aluminum construction Includes fully-serviceable thermostat for fast warm-up in cold climates and thermostat bypass for constant cooling in hot climates Helps extend transmission life and prevent overheating Fits with stock transmission cooler piping, requiring no modification for installation Integrated heat-sink fins provide unique styling and added heat dissipation Durable anodized finish Mishimoto Lifetime Warranty Attributes: GTIN: 00840197702819 Brand Name: Mishimoto TechSpec Chassis Codes: WK2 TechSpec Includes: (1) CNC-Machined Billet Aluminum Thermal Bypass Valve--(1) Removable Thermostat--(1) Removable Thermostat Bypass w/ Installation Hardware--(1) Assembly Notecard--Mishimoto Lifetime Warranty TechSpec Note: Mishimoto does not recommend customers in cold climates install the thermostat bypass to avoid overcooling of the transmission fluid TechSpec Mishimoto Activation Temperature (F): 160 TechSpec OEM Activation Temperature (F): N/A SellingPoint01: Direct fit for 2016-2020 Jeep Grand Cherokee 3.0L/5.7L/6.4L SellingPoint02: Installs in less than 1 hour SellingPoint03: Eliminates failure-prone bypass valve SellingPoint04: Durable CNC-machined billet aluminum construction SellingPoint05: Includes fully-serviceable thermostat for fast warm-up in cold climates and thermostat bypass for constant cooling in hot climates SellingPoint06: Helps extend transmission life and prevent overheating SellingPoint07: Fits with stock transmission cooler piping, requiring no modification for installation SellingPoint08: Integrated heat-sink fins provide unique styling and added heat dissipation SellingPoint09: Durable anodized finish SellingPoint10: Mishimoto Lifetime Warranty SellingPoint11: N/A SellingPoint12: N/A SellingPoint13: N/A SellingPoint14: N/A SellingPoint15: N/A Install Difficulty: 1 TechSpec Applications: Jeep Grand Cherokee V6 (3.0L EcoDiesel) 2016-2019 (8HP70 / 8HP75)--Jeep Grand Cherokee V8 (5.7L) 2016-2021 (8HP70)--Jeep Grand Cherokee V8 (6.4L) 2016-2021 (8HP70)--Jeep Grand Cherokee Trackhawk V8 (6.2L) 2018 (8HP95) TechSpec Engine Codes: L630 EcoDiesel--5.7L Hemi--6.4L Hemi Extended Information: Country of Origin: China Life Cycle Status: Available To Order Packing Information: Quantity of Each: 1 Package UOM: EA Dimension: 8 x 7 x 2 inches Weight: 1 lb

The Jeep JK is known to experience high transmission fluid temperatures, especially when off-roading or driving in hot climates.Mishimoto has developed an ideal upgrade for reducing temperatures with our direct-fit transmission cooler kit, engineered specifically for the JK chassis.This kit uses precision-engineered brackets to mount a large 19-row cooler in the front grille area, thus maximizing airflow and providing significant increases in cooling efficiency.This kIt'significantly reduces transmission fluid temperatures, resulting in decreased transmission wear and improved vehicle safety.The Mishimoto Jeep JK Transmission Cooler Kit includes all lines and hardware necessary for an easy installation.This kit is a perfect complement to the Mishimoto Jeep JK oil cooler kit and the Mishimoto all-aluminum radiator for the ultimate cooling solution for your Jeep JK.As with all our products, this kit includes the Mishimoto lifetime warranty. Direct fit for 2007-2011 Jeep Wrangler JK 19-row bar-and-plate oil cooler for efficient cooling Reduces transmission fluid temperatures to prevent damage and reduce wear Includes brackets for easy installation Includes lines and fittings for leak-free performance Mishimoto Lifetime Warranty Attributes: GTIN: 00748354009545 Brand Name: Mishimoto TechSpec Rows: 19 TechSpec Core Construction: N/A TechSpec Core Length (in): 11 TechSpec Core Height (in): 5.43 TechSpec Core Thickness (in): 1.97 TechSpec Engine Codes: EGH TechSpec Chassis Codes: JK TechSpec Installation Notes: 22 in-lbs recommended for all worm-gear clamps.--These clamps have an operating range of 18-27 in- 2-3NM.--Do not exceed the maximum torque rating of 27 in-lbs----Recommended torque specification for all straight fittings and banjo bolts: 15-25 lb-ftDo not exceed the maximum torque rating of 35 ft-lb TechSpec Caution: It is the installer's responsibility to check all thermostat plugs, NPT plugs, line fittings, and other connections to assure they are fully tightened before operating the vehicle. Mishimoto recommends that you check all connections at regular intervals, especially during the first few miles after installation. For additional technical information, contact our customer experience team. TechSpec Overall Height (in): 12.95 TechSpec Overall Length (in): 6.44 TechSpec Overall Width (in): 1.97 TechSpec Inlet: -10AN TechSpec Outlet: -10AN TechSpec Includes: Application Specific Mounting Brackets--19-Row Oil Cooler--6ft Black Rubber 3/8-in Transmission--45 -10AN to 3/8-in Barbed Push-On Fittings--Brass 90 Barbed Push-On Fittings--Worm Gear Clamps--Mounting Hardware Set--Mishimoto Lifetime Warranty TechSpec Applications: 2007-2011 Jeep Wrangler--2007-2011 Jeep Wrangler Unlimited TechSpec Fluid Capacity (qts): N/A TechSpec Note: Requires modification to factory transmission cooler lines. SellingPoint01: Direct fit for 2007-2011 Jeep Wrangler JK SellingPoint02: 19-row bar-and-plate oil cooler for efficient cooling SellingPoint03: Reduces transmission fluid temperatures to prevent damage and reduce wear SellingPoint04: Includes brackets for easy installation SellingPoint05: Includes lines and fittings for leak-free performance SellingPoint06: Mishimoto Lifetime Warranty SellingPoint07: N/A SellingPoint08: N/A SellingPoint09: N/A SellingPoint10: N/A SellingPoint11: N/A SellingPoint12: N/A SellingPoint13: N/A SellingPoint14: N/A SellingPoint15: N/A Install Difficulty: 3 OptionLabel: Silver Extended Information: Country of Origin: China Life Cycle Status: Available To Order Packing Information: Quantity of Each: 1 Package UOM: EA Dimension: 18 x 8 x 14.5 inches Weight: 9.5 lb

Keep your 2020+ Toyota GR Supra 3.0L shifting with the Mishimoto Automatic Transmission cooler. While many enthusiasts might miss the third pedal on the latest Supra’s floor, the quick-thinking ZF 8HP mated with the B58 more than makes up for it. However, even with the latest transmission technology, the age-old enemy to sports cars rears its head: heat. The tag team at Toyota and BMW were already ahead of the game by fitting the A90 Supra with an external liquid-to-air transmission cooler, but heavy demand can still be too much. With plenty of room to grow, our engineering team expanded the transmission cooler’s core, increasing the volume by 162-percent and the external fin surface area by 412-percent while retaining similar fluid pressures within the system. We also incorporated internal cooling fins to maximize cooling power to maintain proper transmission temperatures, perfect for long days at the track or a spirited drive through the backroads.The Mishimoto Automatic Transmission Cooler for your 2020+ Toyota GR Supra accomplishes all of this with a lightweight, aluminum tube-and-fin core, powder-coated in a sleek silver finish. As with all of our products, this transmission cooler also includes the Mishimoto Lifetime Warranty for a worry-free installation. Direct fit for the 2020+ Toyota GR Supra 3.0L162% increase in core volume 162% increase in core volume 412% increase in external fin surface area Incorporates internal cooling fins for maximum cooling potential Designed to minimize pressure drop for maximum flow through system Mishimoto Lifetime Warranty Attributes: GTIN: 00811580039867 Brand Name: Mishimoto TechSpec Rows: N/A TechSpec Core Construction: N/A TechSpec Core Length (in): N/A TechSpec Core Height (in): N/A TechSpec Core Thickness (in): N/A TechSpec Engine Codes: N/A TechSpec Chassis Codes: N/A TechSpec Installation Notes: N/A TechSpec Caution: N/A TechSpec Overall Height (in): 7.1 TechSpec Overall Length (in): 26 TechSpec Overall Width (in): 1.4 TechSpec Inlet: N/A TechSpec Outlet: N/A TechSpec Includes: Transmission Cooler--Mishimoto Lifetime Warranty TechSpec Applications: N/A TechSpec Fluid Capacity (qts): N/A TechSpec Note: N/A SellingPoint01: Direct fit for the 2020+ Toyota GR Supra 3.0L SellingPoint02: 162-percent increase in core volume SellingPoint03: 412-percent increase in external fin surface area SellingPoint04: Incorporates internal cooling fins for maximum cooling potential SellingPoint05: Designed to minimize pressure drop for maximum flow through system SellingPoint06: Mishimoto Lifetime Warranty SellingPoint07: N/A SellingPoint08: N/A SellingPoint09: N/A SellingPoint10: N/A SellingPoint11: N/A SellingPoint12: N/A SellingPoint13: N/A SellingPoint14: N/A SellingPoint15: N/A Install Difficulty: 2 Extended Information: Country of Origin: China Life Cycle Status: Available To Order Packing Information: Quantity of Each: 1 Package UOM: EA Dimension: 29 x 5 x 10 inches Weight: 11 lb

The Jeep JK is known to experience high transmission fluid temperatures, especially when off-roading or driving in hot climates.Mishimoto has developed an ideal upgrade for reducing temperatures with our direct-fit transmission cooler kit, engineered specifically for the JK chassis.This kit uses precision-engineered brackets to mount a large 19-row cooler in the front grille area, thus maximizing airflow and providing significant increases in cooling efficiency.This kIt'significantly reduces transmission fluid temperatures, resulting in decreased transmission wear and improved vehicle safety.The Mishimoto Jeep JK Transmission Cooler Kit includes all lines and hardware necessary for an easy installation.This kit is a perfect complement to the Mishimoto Jeep JK oil cooler kit and the Mishimoto all-aluminum radiator for the ultimate cooling solution for your Jeep JK.As with all our products, this kit includes the Mishimoto lifetime warranty. Direct fit for 2007-2011 Jeep Wrangler JK 19-row bar-and-plate oil cooler for efficient cooling Reduces transmission fluid temperatures to prevent damage and reduce wear Includes brackets for easy installation Includes lines and fittings for leak-free performance Mishimoto Lifetime Warranty Attributes: GTIN: 00748354009552 Brand Name: Mishimoto SellingPoint03: Reduces transmission fluid temperatures to prevent damage and reduce wear SellingPoint04: Includes brackets for easy installation SellingPoint05: Includes lines and fittings for leak-free performance SellingPoint06: Mishimoto Lifetime Warranty SellingPoint07: N/A SellingPoint08: N/A SellingPoint09: N/A SellingPoint10: N/A SellingPoint11: N/A SellingPoint12: N/A SellingPoint13: N/A SellingPoint14: N/A SellingPoint15: N/A Install Difficulty: 3 OptionLabel: Black TechSpec Rows: 19 TechSpec Core Construction: N/A TechSpec Core Length (in): 11 TechSpec Core Height (in): 5.43 TechSpec Core Thickness (in): 1.97 TechSpec Engine Codes: EGH TechSpec Chassis Codes: JK TechSpec Installation Notes: 22 in-lbs recommended for all worm-gear clamps.--These clamps have an operating range of 18-27 in- 2-3NM.--Do not exceed the maximum torque rating of 27 in-lbs----Recommended torque specification for all straight fittings and banjo bolts: 15-25 lb-ftDo not exceed the maximum torque rating of 35 ft-lb TechSpec Caution: It is the installer's responsibility to check all thermostat plugs, NPT plugs, line fittings, and other connections to assure they are fully tightened before operating the vehicle. Mishimoto recommends that you check all connections at regular intervals, especially during the first few miles after installation. For additional technical information, contact our customer experience team. TechSpec Overall Height (in): 12.95 TechSpec Overall Length (in): 6.44 TechSpec Overall Width (in): 1.97 TechSpec Inlet: -10AN TechSpec Outlet: -10AN TechSpec Includes: Application Specific Mounting Brackets--19-Row Oil Cooler--6ft Black Rubber 3/8-in Transmission--45 -10AN to 3/8-in Barbed Push-On Fittings--Brass 90 Barbed Push-On Fittings--Worm Gear Clamps--Mounting Hardware Set--Mishimoto Lifetime Warranty TechSpec Applications: 2007-2011 Jeep Wrangler--2007-2011 Jeep Wrangler Unlimited TechSpec Fluid Capacity (qts): N/A TechSpec Note: Requires modification to factory transmission cooler lines. SellingPoint01: Direct fit for 2007-2011 Jeep Wrangler JK SellingPoint02: 19-row bar-and-plate oil cooler for efficient cooling Extended Information: Country of Origin: China Life Cycle Status: Available To Order Packing Information: Quantity of Each: 1 Package UOM: EA Dimension: 18 x 8 x 14.5 inches Weight: 9.5 lb

The transmission is the backbone of your Grand Cherokee. It's responsible for transmitting large quantities of torque from your V8 or 3.0L EcoDiesel powerplant. That much torque generates a lot of heat, and if that heat isn't dissipated, it can destroy your transmission. The transmission cooler does a good job of keeping trans fluid temperatures in check, but only if the fluid can reach it. The stock cooling system of the 8HP transmission utilizes an in-line thermal bypass valve that controls fluid flow to the transmission cooler. The purpose of this valve is to prevent transmission fluid from flowing to the cooler until it reaches operating temperature. The thermostat inside this valve is prone to failure, however, and when that happens, the fluid never flows to the cooler, and the transmission can overheat. That's why Mishimoto has developed a full-flow thermal bypass valve upgrade for your 2016-2020 Jeep Grand Cherokee. The Mishimoto thermal bypass valve kit includes an all-aluminum CNC-machined housing that replaces the stock unit. This full-flow valve allows fluid to pump through the cooler as soon as the vehicle is started, eliminating the potential failure point of the stock bypass and providing cooling benefits. The full-flow design is beneficial to vehicles operating in hot climates, extreme driving conditions, or towing heavy loads. As with Mishimoto products, this Full-Flow Transmission Thermal Bypass Valve Kit includes our signature Lifetime Warranty. Direct fit for 2016-2020 Jeep Grand Cherokee 3.0L/5.7L/6.4L Installs in less than 1 hour Eliminates failure-prone bypass valve Durable CNC-machined billet aluminum construction Full-flow bypass allows the transmission cooler to operate at maximum efficiency Helps extend transmission life and prevent overheating Fits with stock transmission cooler piping, requiring no modification for installation Integrated heat-sink fins provide unique styling and added heat dissipation Durable anodized finish Mishimoto Lifetime Warranty Attributes: GTIN: 00840197706077 Brand Name: Mishimoto TechSpec Applications: Jeep Grand Cherokee V6 (3.0L EcoDiesel) 2016-2019 (8HP70 / 8HP75)--Jeep Grand Cherokee V8 (5.7L) 2016-2021 (8HP70)--Jeep Grand Cherokee V8 (6.4L) 2016-2021 (8HP70)--Jeep Grand Cherokee Trackhawk V8 (6.2L) 2018 (8HP95) TechSpec Engine Codes: L630 EcoDiesel--5.7L Hemi--6.4L Hemi TechSpec Chassis Codes: WK2 TechSpec Includes: (1) CNC-Machined Billet Aluminum Thermal Bypass Valve--(1) 3/4-inch x 16 Quick-Disconnect Transmission Line Fitting--Mishimoto Lifetime Warranty TechSpec Note: This full-flow bypass valve only fits vehicles with 8-speed automatic transmissionsMishimoto does not recommend customers in cold climates install the thermostat bypass to avoid overcooling of the transmission fluid TechSpec Mishimoto Activation Temperature (F): N/A TechSpec OEM Activation Temperature (F): N/A SellingPoint01: Direct fit for 2016-2020 Jeep Grand Cherokee 3.0L/5.7L/6.4L SellingPoint02: Installs in less than 1 hour SellingPoint03: Eliminates failure-prone bypass valve SellingPoint04: Durable CNC-machined billet aluminum construction SellingPoint05: Full-flow bypass allows the transmission cooler to operate at maximum efficiency SellingPoint06: Helps extend transmission life and prevent overheating SellingPoint07: Fits with stock transmission cooler piping, requiring no modification for installation SellingPoint08: Integrated heat-sink fins provide unique styling and added heat dissipation SellingPoint09: Durable anodized finish SellingPoint10: Mishimoto Lifetime Warranty SellingPoint11: N/A SellingPoint12: N/A SellingPoint13: N/A SellingPoint14: N/A SellingPoint15: N/A Install Difficulty: 1 Extended Information: Country of Origin: China Life Cycle Status: Available To Order Packing Information: Quantity of Each: 1 Package UOM: EA Dimension: 8 x 7 x 2 inches Weight: 1 lb

Keeping transmission fluid temperatures in check is key to extending the life of your transmission. High fluid temperatures cause reduced lubrication, which can damage seals, clutches, and bearings. Mishimoto has a solution with our highly efficient universal 13-row stacked-plate transmission cooler kit. This universal kit applies to any vehicle needing an ancillary cooler to assist in hot climates, towing, or extreme driving conditions. Our heat exchanger features a 40,000 GVW rating, making it ideal for heavy-duty applications. Within this transmission cooler kit, we include the necessary components for a typical installation. The included ¾-in-16 to 3/8-in hose barb adapter fittings feature an integrated O-ring for leak-free operation. Fifty feet of durable SAE J1532 transmission cooler hose is provided to route fluid to and from the transmission. SAE J1532 hose is explicitly designed for transmission fluids and features a spiral polyester reinforcement for increased pressure tolerance. Because routing of fluid lines is often around sharp objects or through tight passageways, we include a durable hose protection sleeve that prevents damage from abrasion. In addition, this transmission cooler includes a durable, corrosion-resistant powder-coated finish. We've included high-quality stainless-steel worm-gear clamps and 3/8-in hose barb unions for mating the hose and fittings. Rounding out our Universal 13-row Stacked Plate Transmission Cooler kit is a set of 4 universal mounting brackets and associated hardware, making installation a breeze. As with all our products, this universal transmission cooler includes the signature Mishimoto Lifetime Warranty. Universal mounting for use in any application Efficient stacked-plate core for optimal performance with minimal pressure loss 40,000 GVW rating makes this cooler ideal for heavy-duty applications Sleek, durable powder-coated finish protects against corrosion Hose protection sleeve prevents damage from abrasion 50-inches of durable SAE J1532 transmission cooler hose for routing fluid to/from the transmission SAE J1532 hose explicitly designed for transmission fluids features a spiral polyester reinforcement for increased pressure tolerance Precise O-ring sealed ¾"-16 to hose barb adapters provide a leak-free seal High-quality stainless-steel worm gear clamps Applicable for use with transmission fluid, power steering fluid, engine oil, and a variety of other automotive fluids Mishimoto Lifetime Warranty Attributes: GTIN: 00840197709146 Brand Name: Mishimoto TechSpec Rows: 13 TechSpec Core Construction: N/A TechSpec Core Length (in): N/A TechSpec Core Height (in): N/A TechSpec Core Thickness (in): N/A TechSpec Engine Codes: N/A TechSpec Chassis Codes: N/A TechSpec Installation Notes: N/A TechSpec Caution: N/A TechSpec Overall Height (in): N/A TechSpec Overall Length (in): N/A TechSpec Overall Width (in): N/A TechSpec Inlet: 3/4-16 TechSpec Outlet: 3/4-16 TechSpec Includes: 13-Row Stacked Plate Transmission Cooler--Universal Mounting Brackets--3/8-in Hose Barb Male to Male Adapter--3/4-16 Male to 3/8-in Barb Fittings--3/8-in ID SAE J1532 Transmission Oil Cooler Hose, 50-in Long--3/8-in Hose Protection Sleeve, 50-in Long--Hose Connection Shrink Wrap--Worm-Gear Clamps--Mounting hardware--Mishimoto Lifetime Warranty TechSpec Applications: N/A TechSpec Fluid Capacity (qts): N/A TechSpec Note: N/A SellingPoint01: Universal mounting for use in any application SellingPoint02: Efficient stacked-plate core for optimal performance with minimal pressure loss SellingPoint03: 40,000 GVW rating makes this cooler ideal for heavy-duty applications SellingPoint04: Sleek, durable powder-coated finish protects against corrosion SellingPoint05: Hose protection sleeve prevents damage from abrasion SellingPoint06: 50-inches of durable SAE J1532 transmission cooler hose for routing fluid to/from the transmission SellingPoint07: SAE J1532 hose explicitly designed for transmission fluids features a spiral polyester reinforcement for increased pressure tolerance SellingPoint08: Precise O-ring sealed ¾-16 to hose barb adapters provide a leak-free seal SellingPoint09: High-quality stainless-steel worm gear clamps SellingPoint10: Applicable for use with transmission fluid, power steering fluid, engine oil, and a variety of other automotive fluids SellingPoint11: Mishimoto Lifetime Warranty SellingPoint12: N/A SellingPoint13: N/A SellingPoint14: N/A SellingPoint15: N/A TechSpec Material: 6061 Aluminum Install Difficulty: N/A OptionLabel: Black Extended Information: Country of Origin: China Life Cycle Status: Available To Order Packing Information: Quantity of Each: 1 Package UOM: EA Dimension: 25 x 3 x 11 inches Weight: 4.97 lb

The transmission is the backbone of your 2013-2018 Dodge Ram 6.7L Cummins. It's responsible for transmitting up to 930 lb-ft of torque from the engine to the wheels. That much power generates a lot of heat, and if that heat isn't dissipated, it can destroy your transmission. The transmission cooler does a good job of keeping trans fluid temperatures in check, but only if the fluid can reach it. The stock cooling system of both the 68-RFE and Aisin AS69RC utilizes an in-line thermal bypass valve that controls fluid flow to the transmission cooler. The purpose of this valve is to prevent transmission fluid from flowing to the cooler until it reaches operating temperature. The thermostat inside this valve is prone to failure, however, and when that happens, the fluid never flows to the cooler, and the transmission can overheat. That's why Mishimoto has developed a full flow thermal bypass valve upgrade for your 2013-2018 Dodge Ram 6.7L Cummins. Our CNC-machined aluminum thermal bypass valve not only looks better than the stock unit, but it performs better too. This Mishimoto thermal bypass valve eliminates the internal thermostat, providing full fluid flow to the transmission cooler in all running conditions. This setup is ideal for owners in warm climates, those performing heavy towing, and trucks needing the best possible cooling efficiency for their transmission. The Mishimoto full-flow thermal bypass valve features strategically machined internal passages, providing improved flow over the stock valve for more effective cooling. In addition, cooling fins machined into the valve body add even more heat dissipation. This 2013-2018 Dodge Ram 6.7L Cummins Thermal Bypass Full Flow Valve Kit is built to last a lifetime with a durable silver anodized finish and our Mishimoto Lifetime Warranty. Direct fit for Dodge Ram 2500/3500 6.7L Cummins, 2013-2018 Installs in less than 1 hour Eliminates failure-prone bypass valve Durable CNC-machined billet aluminum construction Full-flow bypass allows the transmission cooler to operate at maximum efficiency Helps extend transmission life and prevent overheating Fits with stock transmission cooler piping, requiring no modification for installation Integrated heat-sink fins provide unique styling and added heat dissipation Durable anodized finish Mishimoto Lifetime Warranty Attributes: GTIN: 00840197704172 Brand Name: Mishimoto TechSpec Applications: Dodge Ram 2500 I6 (6.7L) 2013-2018--Dodge Ram 3500 I6 (6.7L) 2013-2018 TechSpec Engine Codes: 6.7 ISB TechSpec Chassis Codes: Ram 2500--Ram 3500 TechSpec Includes: (1) CNC-Machined Billet Aluminum Thermal Bypass Valve--(2) 3/4-inch x 16 Quick-Disconnect Transmission Line Fittings--Mishimoto Lifetime Warranty TechSpec Note: Mishimoto does not recommend customers in cold climates install the thermostat bypass to avoid overcooling of the transmission fluid TechSpec Mishimoto Activation Temperature (F): N/A TechSpec OEM Activation Temperature (F): N/A SellingPoint01: Direct fit for Dodge Ram 2500/3500 6.7L Cummins, 2013-2018 SellingPoint02: Installs in less than 1 hour SellingPoint03: Eliminates failure-prone bypass valve SellingPoint04: Durable CNC-machined billet aluminum construction SellingPoint05: Full-flow bypass allows the transmission cooler to operate at maximum efficiency SellingPoint06: Helps extend transmission life and prevent overheating SellingPoint07: Fits with stock transmission cooler piping, requiring no modification for installation SellingPoint08: Integrated heat-sink fins provide unique styling and added heat dissipation SellingPoint09: Durable anodized finish SellingPoint10: Mishimoto Lifetime Warranty SellingPoint11: N/A SellingPoint12: N/A SellingPoint13: N/A SellingPoint14: N/A SellingPoint15: N/A Install Difficulty: 1 Extended Information: Country of Origin: China Life Cycle Status: Available To Order Packing Information: Quantity of Each: 1 Package UOM: EA Dimension: 8 x 7 x 2 inches Weight: 1 lb

The factory transmission oil cooler on your 2003-2007 Dodge Ram 5.9L Cummins is a liquid-to-liquid cooling unit, utilizing the engine’s cooling system to cool the transmission fluid during warm outside temperatures and warm the fluid during cold outside temperatures. This design is tried and true, and it works. Until it doesn’t. When they wear out and fail, it can leak coolant into your transmission fluid. Mixing coolant into your transmission fluid can have catastrophic results, and nobody wants to spend thousands of dollars to rebuild or replace their transmission if it can be avoided. The Mishimoto Replacement Transmission Oil Cooler is a direct fit, OEM replacement that requires no modification to install. Made to OEM specifications, this transmission oil cooler is equivalent to an OEM part. By replacing your transmission cooler preventatively, you can save your transmission from falling victim to premature failure. As with all of our products, this cooler is backed by our signature Mishimoto Lifetime Warranty. Direct fit for 2003-2007 Dodge Ram 5.9L Cummins Replaces leaking or failing factory transmission oil cooler Durable, corrosion-resistant aluminum construction Equivalent to OEM specifications for fit and function Includes bracket for easy installation Utilizes all factory lines and hardware No modification required for installation Includes Mishimoto Lifetime Warranty Attributes: GTIN: 00840197710593 Brand Name: Mishimoto SellingPoint01: Direct fit for 2003-2007 Dodge Ram 5.9L Cummins SellingPoint02: Includes new powdercoated bracket and brass fittings for easy installation SellingPoint03: Durable, corrosion-resistant aluminum construction SellingPoint04: Equivalent to OEM specifications for fit and function SellingPoint05: Replaces leaking or failing factory transmission oil cooler SellingPoint15: N/A SellingPoint06: Utilizes all factory lines and hardware SellingPoint07: No modification required for installation SellingPoint08: Includes Mishimoto Lifetime Warrant SellingPoint09: N/A SellingPoint10: N/A SellingPoint11: N/A SellingPoint12: N/A SellingPoint13: N/A SellingPoint14: N/A Install Difficulty: 2 TechSpec Overall Height (in): 6.34 TechSpec Applications: 2003-2007 Dodge Ram 5.9L Cummins TechSpec Includes: (1) Replacement Transmission Oil Cooler--(1) Bracket--(2) -8AN Fittings--Mishimoto Lifetime Warranty TechSpec Outlet: N/A TechSpec Inlet: N/A TechSpec Overall Width (in): 5.79 TechSpec Overall Length (in): 18.87 TechSpec Rows: 23 TechSpec Caution: N/A TechSpec Installation Notes: N/A TechSpec Chassis Codes: N/A TechSpec Engine Codes: Cummins TechSpec Core Thickness (in): 2.87 TechSpec Core Height (in): 3.66 TechSpec Core Length (in): 7.6 TechSpec Core Construction: Stacked-plate TechSpec Fluid Capacity (qts): N/A Extended Information: Country of Origin: China Life Cycle Status: Available To Order Packing Information: Quantity of Each: 1 Package UOM: EA Dimension: 12 x 7 x 6 inches Weight: 3.04 lb

There's no greater enemy for a transmission than heat. Whether your 1994-2002 Dodge Ram 5.9L Cummins is a dedicated tow vehicle, hardworking fleet truck, or a daily driver with a liking for the drag-strip, you need to ensure that your transmission runs cool. Luckily, Mishimoto has developed a direct-fit transmission cooler to do just that. Our 1994-2002 Dodge Ram 5.9L Cummins transmission cooler utilizes a tube-and-fin core for reliable and powerful cooling. The Mishimoto transmission cooler boasts a 116-percent greater core volume, 141-percent increase in fluid capacity, and 134-percent greater fin surface area than the stock 1994-2002 Dodge Ram 5.9L Cummins transmission cooler. If you've ever removed the stock transmission cooler from a 2nd Gen Ram, you probably know that the quick-disconnect fittings are usually not quick anymore. To save you the hassle of removing seized fittings, Mishimoto provides two CNC-machined, stainless steel hose barb fittings so you can cut to the chase, literally. These fittings and the supplied transmission fluid hose allow you to remove the quick-disconnect fittings and connect the stock soft-line to the Mishimoto cooler. Like all Mishimoto products, this transmission cooler is backed up by our Lifetime Warranty with Accident Protection for worry free cooling as long as you own it. Mishimoto Lifetime Warranty Fits all 1994-2002 Dodge Ram 5.9L Cummins 116-percent Increase in core volume 141-percent Increase in fluid capacity 134-percent Increase in fin surface area Attributes: GTIN: 00811580032530 Brand Name: Mishimoto TechSpec Rows: 22 TechSpec Core Construction: N/A TechSpec Core Length (in): 16.8 TechSpec Core Height (in): 8.5 TechSpec Core Thickness (in): 1.4 TechSpec Engine Codes: N/A TechSpec Chassis Codes: N/A TechSpec Installation Notes: N/A TechSpec Caution: N/A TechSpec Overall Height (in): N/A TechSpec Overall Length (in): N/A TechSpec Overall Width (in): N/A TechSpec Inlet: N/A TechSpec Outlet: N/A TechSpec Includes: Mishimoto Tube-and-Fin Transmission Cooler--CNC-Machined Stainless Steel Hose Barb Fittings--29.5-in Transmission Hose--Worm Gear Clamps--Mounting Hardware--Mishimoto Lifetime Warranty TechSpec Applications: N/A TechSpec Fluid Capacity (qts): 0.66 TechSpec Note: This kit requires cutting of the stock transmission cooler lines to remove the quick-disconnect fittings. Mishimoto provides CNC-machined stainless steel hose barb fittings to splice the supplied transmission cooler line with the stock soft-lblines. Please see installation instructions for more details.----Vehicles equipped with aftermarket intercoolers may require slight trimming of the bumper to fit this transmission cooler. SellingPoint01: Fits all 1994-2002 Dodge Ram 5.9L Cummins SellingPoint02: 116-percent Increase in core volume SellingPoint03: 141-percent Increase in fluid capacity SellingPoint04: 134-percent Increase in fin surface area SellingPoint05: Tube-and-fin design for tough and reliable cooling SellingPoint06: Eliminates corrosion-prone quick-disconnect fittings SellingPoint07: Patent numberD905,115 SellingPoint08: Mishimoto Lifetime Warranty SellingPoint09: N/A SellingPoint10: N/A SellingPoint11: N/A SellingPoint12: N/A SellingPoint13: N/A SellingPoint14: N/A SellingPoint15: N/A Install Difficulty: 4 Extended Information: Country of Origin: China Life Cycle Status: Available To Order Packing Information: Quantity of Each: 1 Package UOM: EA Dimension: 24 x 6 x 14 inches Weight: 11 lb

There’s no greater enemy for a transmission than heat. Whether your 2015-2018 RAM 6.7L Cummins is a dedicated tow vehicle, hardworking fleet truck, or a daily driver with a liking for the dragstrip, you need to ensure that your transmission runs cool. Luckily, Mishimoto has developed a direct-fit transmission cooler to do just that. Our 2015-2018 RAM 6.7L Cummins transmission cooler utilizes a tube-and-fin core with internal fins to balance flow with efficient cooling. With a massive 112-percent greater core volume, 237-percent increase in fin area, and 226-percent increase in fluid capacity, this trans cooler is a huge improvement over the stock unit. To make even better use of that extra core volume, the Mishimoto transmission cooler utilizes fins within the tubes to not only add more cooling surface area, but also ensure more of the fluid contacts the tube, leading to better cooling efficiency. All these improvements make the Mishimoto transmission cooler the ideal replacement for your stock transmission cooler.Installation of the Mishimoto 2015-2018 RAM 6.7L Cummins transmission cooler requires no cutting or other modifications and includes all hardware needed for a fast and easy install. Like all Mishimoto products, this transmission cooler is backed up by our Lifetime Warranty with Accident Protection for worry free cooling as long as you own it. Direct fit for 2015-2018 RAM 6.7L Cummins 112% increase in core volume over stock cooler 237% increase in external fin area over stock cooler 226% increase in fluid capacity over stock cooler Internal fins distribute fluid throughout the tube for more efficient cooling Patent #D940,014 Mishimoto Lifetime Warranty Attributes: GTIN: 00811580038297 Brand Name: Mishimoto TechSpec Rows: N/A TechSpec Core Construction: N/A TechSpec Core Length (in): 24.76 TechSpec Core Height (in): 11.85 TechSpec Core Thickness (in): 1.25 TechSpec Engine Codes: 6.7L Cummins TechSpec Chassis Codes: N/A TechSpec Installation Notes: N/A TechSpec Caution: N/A TechSpec Overall Height (in): N/A TechSpec Overall Length (in): N/A TechSpec Overall Width (in): N/A TechSpec Inlet: N/A TechSpec Outlet: N/A TechSpec Includes: Mishimoto Transmission Cooler--Aluminum Spacers--Quick-Disconnect Fittings--Mounting Hardware--Mishimoto Lifetime Warranty TechSpec Applications: 2015-2018 RAM 2500 6.7L Cummins--2015-2018 RAM 3500 6.7L Cummins TechSpec Fluid Capacity (qts): 0.767 TechSpec Note: N/A SellingPoint01: Direct fit for 2015-2018 RAM 6.7L Cummins SellingPoint02: 112-percent increase in core volume over stock cooler SellingPoint03: 237-percent increase in external fin area over stock cooler SellingPoint04: 226-percent increase in fluid capacity over stock cooler SellingPoint05: Internal fins distribute fluid throughout the tube for more efficient cooling SellingPoint06: Patent numberD940,014 SellingPoint07: Mishimoto Lifetime Warranty SellingPoint08: N/A SellingPoint09: N/A SellingPoint10: N/A SellingPoint11: N/A SellingPoint12: N/A SellingPoint13: N/A SellingPoint14: N/A SellingPoint15: N/A Install Difficulty: 3 Extended Information: Country of Origin: China Life Cycle Status: Available To Order Packing Information: Quantity of Each: 1 Package UOM: EA Dimension: 37 x 4 x 17 inches Weight: 19 lb

There’s no greater enemy for a transmission than heat. Whether your 2013-2014 RAM 6.7L Cummins is a dedicated tow vehicle, hardworking fleet truck, or a daily driver with a liking for the dragstrip, you need to ensure that your transmission runs cool. Luckily, Mishimoto has developed a direct-fit transmission cooler to do just that. Our 2013-2014 RAM 6.7L Cummins transmission cooler utilizes a tube-and-fin core with internal fins to balance flow with efficient cooling. With a massive 82% greater core volume, 112% increase in fin area, and 1.34-quart fluid capacity for improved cooling capacity, this trans cooler is a huge improvement over the stock unit. To make even better use of that extra core volume, the Mishimoto transmission cooler utilizes fins within the tubes to not only add more cooling surface area, but also ensure more of the fluid contacts the tube, leading to better cooling efficiency. All these improvements make the Mishimoto transmission cooler the ideal replacement for your stock transmission cooler. Installation of the Mishimoto 2013-2014 RAM 6.7L Cummins transmission cooler requires no cutting or other modifications. Like all Mishimoto products, this transmission cooler is backed up by our Lifetime Warranty with Accident Protection for worry free cooling as long as you own it. Direct fit for 2015-2018 RAM 6.7L Cummins 82% increase in core volume over stock cooler 112% increase in external fin area over stock cooler 1.34-quart fluid capacity for improved cooling capacity Internal fins distribute fluid throughout the tube for more efficient cooling Mishimoto Lifetime Warranty Attributes: GTIN: 00840197711422 Brand Name: Mishimoto TechSpec Rows: 26 TechSpec Core Construction: N/A TechSpec Core Length (in): 23.62 TechSpec Core Height (in): 10.67 TechSpec Core Thickness (in): 1.26 TechSpec Engine Codes: N/A TechSpec Chassis Codes: N/A TechSpec Installation Notes: N/A TechSpec Caution: N/A TechSpec Overall Height (in): 12.13 TechSpec Overall Length (in): 30.55 TechSpec Overall Width (in): 1.53 TechSpec Inlet: N/A TechSpec Outlet: N/A TechSpec Includes: Mishimoto Transmission Cooler--Quick-Disconnect Fittings--Mishimoto Lifetime Warranty TechSpec Applications: 2013-2014 RAM 2500 6.7L Cummins--2013-2014 RAM 3500 6.7L Cummins TechSpec Fluid Capacity (qts): 1.34 TechSpec Note: N/A SellingPoint01: Direct fit for 2013-2014 RAM 6.7L Cummins SellingPoint02: 82-percent increase in core volume over stock cooler SellingPoint03: 112-percent increase in external fin area over stock cooler SellingPoint04: 1.34-quart fluid capacity for improved cooling capacity SellingPoint05: Internal fins distribute fluid throughout the tube for more efficient cooling SellingPoint06: Mishimoto Lifetime Warranty SellingPoint07: N/A SellingPoint08: N/A SellingPoint09: N/A SellingPoint10: N/A SellingPoint11: N/A SellingPoint12: N/A SellingPoint13: N/A SellingPoint14: N/A SellingPoint15: N/A Install Difficulty: 3 Extended Information: Country of Origin: China Life Cycle Status: Available To Order Packing Information: Quantity of Each: 1 Package UOM: EA Dimension: 33 x 4 x 15 inches Weight: 15 lb

Keeping transmission fluid temperatures in check is key to extending the life of your transmission. High fluid temperatures cause reduced lubrication, which can damage seals, clutches, and bearings. Mishimoto has a solution with our highly efficient universal 13-row stacked-plate transmission cooler kit. This universal kit applies to any vehicle needing an ancillary cooler to assist in hot climates, towing, or extreme driving conditions. Our heat exchanger features a 40,000 GVW rating, making it ideal for heavy-duty applications. Within this transmission cooler kit, we include the necessary components for a typical installation. The included ¾-in-16 to 3/8-in hose barb adapter fittings feature an integrated O-ring for leak-free operation. Fifty feet of durable SAE J1532 transmission cooler hose is provided to route fluid to and from the transmission. SAE J1532 hose is explicitly designed for transmission fluids and features a spiral polyester reinforcement for increased pressure tolerance. Because routing of fluid lines is often around sharp objects or through tight passageways, we include a durable hose protection sleeve that prevents damage from abrasion. In addition, this transmission cooler includes a durable, corrosion-resistant powder-coated finish. We've included high-quality stainless-steel worm-gear clamps and 3/8-in hose barb unions for mating the hose and fittings. Rounding out our Universal 13-row Stacked Plate Transmission Cooler kit is a set of 4 universal mounting brackets and associated hardware, making installation a breeze. As with all our products, this universal transmission cooler includes the signature Mishimoto Lifetime Warranty. Universal mounting for use in any application Efficient stacked-plate core for optimal performance with minimal pressure loss 40,000 GVW rating makes this cooler ideal for heavy-duty applications Sleek, durable powder-coated finish protects against corrosion Hose protection sleeve prevents damage from abrasion 50-inches of durable SAE J1532 transmission cooler hose for routing fluid to/from the transmission SAE J1532 hose explicitly designed for transmission fluids features a spiral polyester reinforcement for increased pressure tolerance Precise O-ring sealed ¾"-16 to hose barb adapters provide a leak-free seal High-quality stainless-steel worm gear clamps Applicable for use with transmission fluid, power steering fluid, engine oil, and a variety of other automotive fluids Mishimoto Lifetime Warranty Attributes: GTIN: 00840197703106 Brand Name: Mishimoto TechSpec Rows: 13 TechSpec Core Construction: N/A TechSpec Core Length (in): N/A TechSpec Core Height (in): N/A TechSpec Core Thickness (in): N/A TechSpec Engine Codes: N/A TechSpec Chassis Codes: N/A TechSpec Installation Notes: N/A TechSpec Caution: N/A TechSpec Overall Height (in): N/A TechSpec Overall Length (in): N/A TechSpec Overall Width (in): N/A TechSpec Inlet: 3/4-16 TechSpec Outlet: 3/4-16 TechSpec Includes: 13-Row Stacked Plate Transmission Cooler--Universal Mounting Brackets--3/8-in Hose Barb Male to Male Adapter--3/4-16 Male to 3/8-in Barb Fittings--3/8-in ID SAE J1532 Transmission Oil Cooler Hose, 50-in Long--3/8-in Hose Protection Sleeve, 50-in Long--Hose Connection Shrink Wrap--Worm-Gear Clamps--Mounting hardware--Mishimoto Lifetime Warranty TechSpec Applications: N/A TechSpec Fluid Capacity (qts): N/A TechSpec Note: N/A SellingPoint01: Universal mounting for use in any application SellingPoint02: Efficient stacked-plate core for optimal performance with minimal pressure loss SellingPoint03: 40,000 GVW rating makes this cooler ideal for heavy-duty applications SellingPoint04: Sleek, durable powder-coated finish protects against corrosion SellingPoint05: Hose protection sleeve prevents damage from abrasion SellingPoint06: 50-inches of durable SAE J1532 transmission cooler hose for routing fluid to/from the transmission SellingPoint07: SAE J1532 hose explicitly designed for transmission fluids features a spiral polyester reinforcement for increased pressure tolerance SellingPoint08: Precise O-ring sealed ¾-16 to hose barb adapters provide a leak-free seal SellingPoint09: High-quality stainless-steel worm gear clamps SellingPoint10: Applicable for use with transmission fluid, power steering fluid, engine oil, and a variety of other automotive fluids SellingPoint11: Mishimoto Lifetime Warranty SellingPoint12: N/A SellingPoint13: N/A SellingPoint14: N/A SellingPoint15: N/A Install Difficulty: N/A Extended Information: Country of Origin: China Life Cycle Status: Available To Order Packing Information: Quantity of Each: 1 Package UOM: EA Dimension: 25 x 3 x 11 inches Weight: 6 lb

The 10R80 transmission found in your 2017+ Ford Raptor 3.5L EcoBoost may be new to the scene, but it's proving capable of handling the power of the Raptor. As with any newly developed product, however, time and mileage tend to reveal any shortcomings. One major weak point of the 10R80 is the factory-equipped thermal bypass valve. This valve controls transmission fluid flow to the external cooler, and many reports of failures are beginning to surface. In these cases, the factory valve is malfunctioning by restricting or eliminating flow to the external cooler, which quickly results in high fluid temps, damaged transmissions, and an array of warnings on your dashboard. To protect your truck from potential transmission damage, the bright minds at Mishimoto have developed a direct-fit full-flow thermal bypass valve kit for your 2017+ Ford Raptor. The Mishimoto thermal bypass valve kit includes an all-aluminum CNC-machined housing that replaces the stock unit. This full-flow valve allows fluid to pump through the cooler as soon as the truck is started, eliminating the potential failure point of the stock bypass, and providing cooling benefits. The full-flow design is very beneficial to vehicles operating in hot climates, extreme driving conditions, or towing heavy loads. Easy install in about 1 hour Eliminates failure-prone bypass valve Full-flow bypass allows the transmission cooler to operate at maximum efficiency Durable CNC-machined billet aluminum design Helps extend transmission life and prevent overheating Fits with stock transmission cooler piping, requiring no modification for installation Machined cooling fins for added heat dissipation Mishimoto Lifetime Warranty Direct fit for Ford Raptor 3.5L EcoBoost 2017+ Attributes: GTIN: 00840197704240 Brand Name: Mishimoto TechSpec Applications: Ford F-150 Raptor V6 (3.5L) 2017-2021 TechSpec Engine Codes: D35 TechSpec Chassis Codes: T3 TechSpec Includes: (1) CNC-Machined Billet Aluminum Thermal Bypass Valve--(1) M18 X 1.5 Plug--(1) Viton O-Ring 15.54mm ID--(2) Viton O-Ring 12.36mm ID--(2) Viton O-Ring 15.3mm ID--Mishimoto Lifetime Warranty TechSpec Note: Mishimoto does not recommend customers in cold climates install the thermostat bypass to avoid overcooling of the transmission fluid TechSpec Mishimoto Activation Temperature (F): N/A TechSpec OEM Activation Temperature (F): N/A SellingPoint01: Direct fit for Ford Raptor 3.5L EcoBoost 2017+ SellingPoint02: Easy install in about 1 hour SellingPoint03: Eliminates failure-prone bypass valve SellingPoint04: Full-flow bypass allows the transmission cooler to operate at maximum efficiency SellingPoint05: Durable CNC-machined billet aluminum design SellingPoint06: Helps extend transmission life and prevent overheating SellingPoint07: Fits with stock transmission cooler piping, requiring no modification for installation SellingPoint08: Machined cooling fins for added heat dissipation SellingPoint09: Mishimoto Lifetime Warranty SellingPoint10: N/A SellingPoint11: N/A SellingPoint12: N/A SellingPoint13: N/A SellingPoint14: N/A SellingPoint15: N/A Install Difficulty: 2 Extended Information: Country of Origin: China Life Cycle Status: Available To Order Packing Information: Quantity of Each: 1 Package UOM: EA Dimension: 6.5 x 6 x 3.2 inches Weight: 1 lb

The 10R80 transmission found in your 2017+ Raptor 3.5L EcoBoost may be new to the scene, but it's proving capable of handling the power of the potent 3.5L. As with any newly developed product, however, time and mileage tend to reveal any shortcomings. One major weak point of the 10R80 is the factory-equipped thermal bypass valve. This valve controls transmission fluid flow to the external cooler, and many reports of failures are beginning to surface. In these cases, the factory valve is malfunctioning by restricting or eliminating flow to the external cooler, which quickly results in high fluid temps, damaged transmissions, and an array of warnings on your dashboard. To protect your truck from potential transmission damage, the bright minds at Mishimoto have developed a direct-fit thermostatic bypass valve kit for your 2017+ Ford Raptor. The Mishimoto thermal bypass valve kit includes an all-aluminum CNC-machined housing that replaces the stock unit. This thermal bypass unit includes a fully serviceable 160F thermostat, providing optimal fluid temperatures for all driving conditions. For those in warm climates or vehicles being used in extreme driving/towing conditions, this kit also includes a bypass assembly that provides full flow to the transmission cooler, regardless of temperature. The Mishimoto thermal bypass valve kit helps extend the life of your 10R80 transmission and effectively eliminates the risk of overheating due to stock bypass valve failure. As with all our products, this kit includes the Mishimoto Lifetime Warranty. Direct fit for Ford Raptor 3.5L EcoBoost 2017+ Easy install in about 1 hour Includes fully serviceable thermostat for fast warm-up in cold climates and thermostat bypass for constant cooling in hot climates Durable CNC-machined billet-aluminum design Helps extend transmission life and prevent overheating Increased flow over stock bypass valve Fits with stock transmission cooler piping, requiring no modification for installation Machined cooling fins for added heat dissipation Durable anodized finish Mishimoto Lifetime Warranty Attributes: GTIN: 00840197702840 Brand Name: Mishimoto TechSpec Applications: Ford F-150 Raptor V6 (3.5L) 2017-2021 TechSpec Engine Codes: D35 TechSpec Chassis Codes: T3 TechSpec Includes: (1) CNC-Machined Billet Aluminum Thermal Bypass Valve--(1) Removable Thermostat--(1) Removable Thermostat Bypass w/ Installation Hardware--(2) Viton O-Ring 12.36mm ID--(2) Viton O-Ring 15.3mm ID--(1) Assembly Notecard--Mishimoto Lifetime Warranty TechSpec Note: Mishimoto does not recommend customers in cold climates install the thermostat bypass to avoid overcooling of the transmission fluid TechSpec Mishimoto Activation Temperature (F): 160 TechSpec OEM Activation Temperature (F): N/A SellingPoint01: Direct fit for Ford Raptor 3.5L EcoBoost 2017+ SellingPoint02: Easy install in about 1 hour SellingPoint03: Includes fully serviceable thermostat for fast warm-up in cold climates and thermostat bypass for constant cooling in hot climates SellingPoint04: Durable CNC-machined billet-aluminum design SellingPoint05: Helps extend transmission life and prevent overheating SellingPoint06: Increased flow over stock bypass valve SellingPoint07: Fits with stock transmission cooler piping, requiring no modification for installation SellingPoint08: Machined cooling fins for added heat dissipation SellingPoint09: Durable anodized finish SellingPoint10: Mishimoto Lifetime Warranty SellingPoint11: N/A SellingPoint12: N/A SellingPoint13: N/A SellingPoint14: N/A SellingPoint15: N/A Install Difficulty: 2 Extended Information: Country of Origin: China Life Cycle Status: Available To Order Packing Information: Quantity of Each: 1 Package UOM: EA Dimension: 6.5 x 6 x 3.2 inches Weight: 1 lb