This K&N cold air intake system is engineered for your RAM 1500 L6-3.0L TT F/L. A high-density polyethylene (HDPE) rotationally molded tube helps increase the volume of airflow to your engine and provides a guaranteed increase of 41.13 horsepower and 67.85 torque with no tune required. This intake system is paired with a washable, reusable High-Flow LIFETIME Air Filter featuring oiled cotton filter media. The oversized, conical design allows you to go up to 100,000 miles between filter services under normal highway driving conditions. A custom designed enclosed air box helps protect intake air from the high temperature of your engine bay, and the entire system can typically be installed in less than 60 minutes.User 1Installation InstructionsThis Part Fits: Year Make Model Submodel 2025 Ram 1500 Big Horn 2025 Ram 1500 Laramie 2025 Ram 1500 Limited 2025 Ram 1500 Limited Longhorn 2025 Ram 1500 Lone Star 2025 Ram 1500 Rebel 2025 Ram 1500 RHO 2025 Ram 1500 Tradesman 2025 Ram 1500 Tradesman HFE 2025 Ram 1500 Tungsten 2025 Ram 1500 Warlock

A high-density polyethylene (HDPE) rotationally-molded tube helps increase the volume of airflow to your engine, and provides a guaranteed increase in horsepower and torque. These systems are paired with a washable, reusable High-Flow Air Filter featuring oiled cotton filter media. The oversized, conical design allows you to go up to 100,000 miles between filter services under normal highway driving conditions. A custom heat shield helps protect intake air from the high temperature of your engine bay, and the entire system can typically be installed in less than 60 minutes. Some intakes are not legal for sale or use on any pollution controlled motor vehicle in California. See the product specifications for CARB status on each part for a specific vehicle.Installation InstructionsUser 1This Part Fits: Year Make Model Submodel 2023 Ford Bronco Raptor

The Banks Monster-Ram is the best-engineered intake elbow (horn) available for the 2019-2024 RAM Cummins 6.7L. Gain responsiveness and power efficiency. Improve Mass Air Flow by 88 percent over the stock intake. Prevents grid heater bolt failure. What it doesThe Monster-Ram improves airflow from the intercooler. It flows 72.7 lbs/min MAF (Mass Air Flow) with Banks&rsquo, High-Flow Heater and Billet Intake Plate compared to stock's 38.6 lbs/min MAF.Monster-Ram raises boost without increasing backpressure at the turbine. The result is a more responsive, power-efficient engine that offers even more headroom than stock for higher horsepower applications.The complete systemBanks' High-Flow Heater and Billet Intake Plate complete the perfect system. The High-Flow Heater allows for the removal of the restrictive stock heater grid plate. The new vertical coil-style heater provides the same functionality for cold starts as the stock grid heater but without obstructing airflow. Replacing the restrictive stock grid heater plate with the Banks High-Flow Intake Plate removes all obstructions and turbulence in the airflow path.How it was designedUtilizing the latest in CFD (computational fluid-dynamics), tested on the flow bench, the dyno, and on-road, Monster-Ram is a beast that only Banks could have unleashed. A direct-replacement aluminum casting, Monster-Ram is instant power, performance, and acceleration gratification. The factory inlet elbow is cramped and angular in order to accommodate the path of the stock No. 1 fuel line. Banks Engineers designed a new No. 1 fuel line, allowing the Monster-Ram to flow more air without obstruction.ExpandableWith four 1/8 inch NPT ports, perfect for temperature and pressure sensors, the sky's the limit for data acquisition.Beats the competitionLike all Banks products, the Monster-Ram was tested against all available competitors. It more than doubles the improvement over the closest competitor.This Part Fits: Year Make Model Submodel 2019-2024 Ram 2500 Big Horn 2019-2024 Ram 2500 Laramie 2019-2021 Ram 2500 Laramie Longhorn 2019-2024 Ram 2500 Limited 2021-2024 Ram 2500 Limited Longhorn 2019-2024 Ram 2500 Lone Star 2023-2024 Ram 2500 Rebel 2024 Ram 2500 Special Service 2019-2024 Ram 2500 Tradesman 2019-2024 Ram 3500 Big Horn 2019-2024 Ram 3500 Laramie 2019-2020 Ram 3500 Laramie Longhorn 2019-2024 Ram 3500 Limited 2021-2024 Ram 3500 Limited Longhorn 2019-2022 Ram 3500 Lone Star 2019-2024 Ram 3500 SLT 2024 Ram 3500 Special Service 2019-2024 Ram 3500 Tradesman

This K&N NextGen cold air intake system is engineered for Dodge Charger V6 3.6L F/I. A high-density polyethylene (HDPE) rotationally molded tube helps increase the volume of airflow by 42.7% to your engine and provides an increase of 14.94 horsepower and 8.22 torque with no tune required. This intake system is paired with a washable, reusable High-Flow LIFETIME Air Filter featuring oiled cotton filter media. The oversized, conical design allows you to go up to 100,000 miles between filter services under normal highway driving conditions. A custom designed NextGen air box helps protect intake air from the high temperature of your engine bay, and the entire system can typically be installed in less than 60 minutes.Installation InstructionsUser 1This Part Fits: Year Make Model Submodel 2011-2014 Chrysler 300 Base 2013-2017 Chrysler 300 C 2013-2014 Chrysler 300 C Luxury 2015-2017 Chrysler 300 C Platinum 2011-2012,2015-2020 Chrysler 300 Limited 2012-2023 Chrysler 300 S 2018-2023 Chrysler 300 Touring 2018-2023 Chrysler 300 Touring L 2017-2023 Dodge Challenger GT 2014 Dodge Challenger Rallye Redline 2011 Dodge Challenger SE 2012-2023 Dodge Challenger SXT 2012,2015-2018 Dodge Challenger SXT Plus 2018-2023 Dodge Charger GT 2018 Dodge Charger GT Plus 2011-2023 Dodge Charger Pursuit 2011-2017 Dodge Charger SE 2012-2023 Dodge Charger SXT 2012,2018 Dodge Charger SXT Plus 2018 Dodge Charger SXT Plus Leather

The Banks Monster-Ram is the best-engineered intake elbow (horn) available for the 2013-2018 RAM Cummins 6.7L. Gain responsiveness and power efficiency. Improve Mass Air Flow by 88 percent over the stock intake. Prevents grid heater bolt failure. What it doesThe Monster-Ram improves airflow from the intercooler. It flows 72.7 lbs/min MAF (Mass Air Flow) with Banks' High-Flow Heater and Billet Intake Plate compared to stock's 38.6 lbs/min MAF.Monster-Ram raises boost without increasing backpressure at the turbine. The result is a more responsive, power-efficient engine that offers even more headroom than stock for higher horsepower applications.The complete systemBank's High-Flow Heater and Billet Intake Plate complete the perfect system. The High-Flow Heater allows for the removal of the restrictive stock heater grid plate. The new vertical coil-style heater provides the same functionality for cold starts as the stock grid heater but without obstructing airflow. Replacing the restrictive stock grid heater plate with the Banks High-Flow Intake Plate removes all obstructions and turbulence in the airflow path.How it was designedUtilizing the latest in CFD (computational fluid-dynamics), tested on the flow bench, the dyno, and on-road, Monster-Ram is a beast that only Banks could have unleashed. A direct-replacement aluminum casting, Monster-Ram is instant power, performance, and acceleration gratification. The factory inlet elbow is cramped and angular in order to accommodate the path of the stock No. 1 fuel line. Banks Engineers designed a new No. 1 fuel line, allowing the Monster-Ram to flow more air without obstruction.ExpandableWith four 1/8 inch NPT ports, perfect for temperature and pressure sensors, the sky's the limit for data acquisition.Beats the competitionLike all Banks products, the Monster-Ram was tested against all available competitors. It more than doubles the improvement over the closest competitor.This Part Fits: Year Make Model Submodel 2013-2018 Ram 2500 Big Horn 2013-2018 Ram 2500 Laramie 2014-2015 Ram 2500 Laramie Limited 2013-2018 Ram 2500 Laramie Longhorn 2016-2018 Ram 2500 Limited 2013-2015 Ram 2500 Lone Star 2013-2016 Ram 2500 Outdoorsman 2013-2018 Ram 2500 SLT 2013 Ram 2500 ST 2013-2018 Ram 2500 Tradesman 2013-2018 Ram 3500 Big Horn 2013-2018 Ram 3500 Laramie 2014-2015 Ram 3500 Laramie Limited 2013-2018 Ram 3500 Laramie Longhorn 2016-2018 Ram 3500 Limited 2013-2015,2017 Ram 3500 Lone Star 2013-2018 Ram 3500 SLT 2013 Ram 3500 ST 2013-2018 Ram 3500 Tradesman

The Banks Monster-Ram is the best-engineered intake elbow (horn) available for the 2007-2012 RAM Cummins 6.7L. Gain responsiveness and power efficiency. Improve Mass Air Flow by 88 percent over the stock intake. Prevents grid heater bolt failure. What it doesThe Monster-Ram improves airflow from the intercooler. It flows 72.7 lbs/min MAF (Mass Air Flow) with Bank's High-Flow Heater and Billet Intake Plate compared to stock's 38.6 lbs/min MAF.Monster-Ram raises boost without increasing backpressure at the turbine. The result is a more responsive, power-efficient engine that offers even more headroom than stock for higher horsepower applications.The complete systemBank's High-Flow Heater and Billet Intake Plate complete the perfect system. The High-Flow Heater allows for the removal of the restrictive stock heater grid plate. The new vertical coil-style heater provides the same functionality for cold starts as the stock grid heater but without obstructing airflow. Replacing the restrictive stock grid heater plate with the Banks High-Flow Intake Plate removes all obstructions and turbulence in the airflow path.How it was designedUtilizing the latest in CFD (computational fluid-dynamics), tested on the flow bench, the dyno, and on-road, Monster-Ram is a beast that only Banks could have unleashed. A direct-replacement aluminum casting, Monster-Ram is instant power, performance, and acceleration gratification. The factory inlet elbow is cramped and angular in order to accommodate the path of the stock No. 1 fuel line. Banks Engineers designed a new No. 1 fuel line, allowing the Monster-Ram to flow more air without obstruction.ExpandableWith four 1/8 inch NPT ports, perfect for temperature and pressure sensors, the sky's the limit for data acquisition.Beats the competitionLike all Banks products, the Monster-Ram was tested against all available competitors. It more than doubles the improvement over the closest competitor.This Part Fits: Year Make Model Submodel 2007-2010 Dodge Ram 2500 Laramie 2007-2010 Dodge Ram 2500 SLT 2007-2010 Dodge Ram 2500 ST 2008-2010 Dodge Ram 2500 SXT 2010 Dodge Ram 2500 TRX 2007-2010 Dodge Ram 3500 Laramie 2007-2010 Dodge Ram 3500 SLT 2007 Dodge Ram 3500 Sport 2007-2010 Dodge Ram 3500 ST 2008-2009 Dodge Ram 3500 SXT 2011-2012 Ram 2500 Laramie 2011-2012 Ram 2500 Laramie Longhorn 2012 Ram 2500 Outdoorsman 2011-2012 Ram 2500 SLT 2011-2012 Ram 2500 ST 2011-2012 Ram 3500 Laramie 2011-2012 Ram 3500 Laramie Longhorn 2011-2012 Ram 3500 SLT 2011-2012 Ram 3500 ST

Gain a guaranteed increase in horsepower and torque with K&N cold air intake system featuring madrel-bent aluminum intake tube. Each system is paired with a washable, reusable High-Flow Air Filter featuring oiled cotton filter media. Some intakes are not legal for sale or use on any pollution-controlled motor vehicle in California. See the product specifications for CARB status on each part for a specific vehicle.Installation InstructionsUser 1This Part Fits: Year Make Model Submodel 2024-2025 Acura Integra Type S 2023-2025 Honda Civic Type R

A high-density polyethylene (HDPE) rotationally-molded tube helps increase the volume of airflow to your engine, and provides a guaranteed increase in horsepower and torque. These systems are paired with a washable, reusable High-Flow Air Filter featuring oiled cotton filter media. The oversized, conical design allows you to go up to 100,000 miles between filter services under normal highway driving conditions. A custom heat shield helps protect intake air from the high temperature of your engine bay, and the entire system can typically be installed in less than 60 minutes. Some intakes are not legal for sale or use on any pollution controlled motor vehicle in California. See the product specifications for CARB status on each part for a specific vehicle.Installation InstructionsUser 1This Part Fits: Year Make Model Submodel 2023-2024 Chevrolet Colorado LT 2023-2024 Chevrolet Colorado Trail Boss 2023-2024 Chevrolet Colorado WT 2023-2024 Chevrolet Colorado Z71 2023-2024 Chevrolet Colorado ZR2 2023-2024 GMC Canyon AT4 2023-2024 GMC Canyon AT4X 2023-2024 GMC Canyon Denali 2023-2024 GMC Canyon Elevation

Gain a guaranteed increase in horsepower and torque with K&N cold air intake system featuring madrel-bent aluminum intake tube. Each system is paired with a washable, reusable High-Flow Air Filter featuring oiled cotton filter media. Some intakes are not legal for sale or use on any pollution-controlled motor vehicle in California. See the product specifications for CARB status on each part for a specific vehicle.Installation InstructionsUser 1This Part Fits: Year Make Model Submodel 2024-2025 Ford Mustang Dark Horse 2024-2025 Ford Mustang Dark Horse Premium 2024-2025 Ford Mustang GT 2024-2025 Ford Mustang GT Premium

Boost your truck’s performance with our high-performance air intake system designed specifically for the Ford F Super Duty. Engineered for enthusiasts who want more horsepower, improved airflow, and stronger acceleration, this system enhances engine output on both diesel and gasoline models. Enjoy the advantages of a K&N air intake system for the Ford F Super Duty and a performance air intake for Ford diesel vehicles—all built for durability and easy installation.Key Features• HDPE rotationally molded tube design that increases engine airflow and boosts horsepower and torque• Washable, reusable high-flow air filter with oiled cotton media—service intervals up to 100,000 miles under normal highway conditions• Custom heat shield to protect intake air from engine bay heat• CARB status compliance details available in the product specificationsInstallation & MaintenanceInstallation is user-friendly and can be completed in less than 60 minutes. For detailed guidance, please refer to our Installation Instructions and additional user resources. With minimal maintenance required, this system is perfect for DIY enthusiasts looking for reliable, long-lasting performance.Vehicle FitmentCompatible models include various trims of the 2017-2019 Ford F-250 Super Duty and F-350 Super Duty. Below is a quick reference: Year Make Model Trim 2017-2019 Ford F-250 Super Duty King Ranch 2017-2019 Ford F-250 Super Duty Lariat 2018-2019 Ford F-250 Super Duty Limited 2017-2019 Ford F-250 Super Duty Platinum 2017-2019 Ford F-250 Super Duty XL 2017-2019 Ford F-250 Super Duty XLT 2017-2019 Ford F-350 Super Duty King Ranch 2017-2019 Ford F-350 Super Duty Lariat 2018-2019 Ford F-350 Super Duty Limited 2017-2019 Ford F-350 Super Duty Platinum 2017-2019 Ford F-350 Super Duty XL 2017-2019 Ford F-350 Super Duty XLT Ready to upgrade your ride? Buy now and experience the difference by browsing our full range in the Air Intake Systems collection.

K&N 2024 Ford Ranger Raptor V6 3.0L NextGen Cold Air Intake

This K&N NextGen cold air intake system is engineered for your RAM 1500 V8-5.7L F/I. A high-density polyethylene (HDPE) rotationally molded tube helps increase the volume of airflow by 36.51% to your engine and provides an increase of 19.94 horsepower and 19.93 torque with no tune required. This intake system is paired with a washable, reusable High-Flow LIFETIME Air Filter featuring oiled cotton filter media. The oversized, conical design allows you to go up to 100,000 miles between filter services under normal highway driving conditions. A custom designed NextGen air box helps protect intake air from the high temperature of your engine bay, and the entire system can typically be installed in less than 60 minutes.Installation InstructionsUser 1

A high-density polyethylene (HDPE) rotationally-molded tube helps increase the volume of airflow to your engine, and provides a guaranteed increase in horsepower and torque. These systems are paired with a washable, reusable High-Flow Air Filter featuring oiled cotton filter media. The oversized, conical design allows you to go up to 100,000 miles between filter services under normal highway driving conditions. A custom heat shield helps protect intake air from the high temperature of your engine bay, and the entire system can typically be installed in less than 60 minutes. Some intakes are not legal for sale or use on any pollution controlled motor vehicle in California. See the product specifications for CARB status on each part for a specific vehicle.Installation InstructionsUser 1This Part Fits: Year Make Model Submodel 2021-2024 Ford Explorer King Ranch 2020-2024 Ford Explorer Platinum 2020-2024 Ford Explorer ST 2020-2023 Lincoln Aviator Base 2020-2024 Lincoln Aviator Black Label 2020-2023 Lincoln Aviator Black Label Grand Touring 2020-2023 Lincoln Aviator Grand Touring 2022-2024 Lincoln Aviator Livery 2024 Lincoln Aviator Premiere 2020-2024 Lincoln Aviator Reserve

Momentum’s innovative filter-to-housing interface was built to feature the largest air filter possible. This 6” tall 360-degree radial flow air filter features a 4.5" flange and our pre-oiled Pro 5R media with five layers of progressively finer cotton gauze media for maximum performance. It provides your engine with the largest amount of high-flowing air and delivers the highest power gains in most cases. This media is perfect for street and/or track use. Its inverted top makes for more filter surface area, resulting in longer service intervals. The one-piece sealed housing, constructed of heat-resistant cross-linked polyethylene (XLPE), features our patent-pending filter-to-housing interface. Its innovative design minimizes the total number of parts, making for an easy installation. A clear sight window allows for hassle-free filter inspection, without having to disassemble your system. Its auxiliary air inlet can be used to bring in additional air from the engine compartment, or can be closed with an included plug. This system features a high quality, computer-designed, dyno-tuned intake tube to achieve maximum power gains while maintaining a perfect fit. Its XLPE material is heat soak resistant and extremely durable. Stainless-steel clamps and bellows silicone coupling are included for strength and durability. Momentum intakes are designed with fewer parts for a fast and easy installation.Installation InstructionsThis Part Fits: Year Make Model Submodel 2021-2024 Lexus IS300 Base 2024 Lexus IS300 F Sport 2024 Lexus IS300 F Sport Design 2021-2024 Lexus IS350 F Sport 2024 Lexus IS350 F Sport Design

The Banks Monster-Ram is the best-engineered intake elbow (horn) available for the 2013-2018 RAM Cummins 6.7L. Gain responsiveness and power efficiency. Improve Mass Air Flow by 88 percent over the stock intake. Prevents grid heater bolt failure. What it doesThe Monster-Ram improves airflow from the intercooler. It flows 72.7 lbs/min MAF (Mass Air Flow) with Banks' High-Flow Heater and Billet Intake Plate compared to stock's 38.6 lbs/min MAF.Monster-Ram raises boost without increasing backpressure at the turbine. The result is a more responsive, power-efficient engine that offers even more headroom than stock for higher horsepower applications.The complete systemBank's High-Flow Heater and Billet Intake Plate complete the perfect system. The High-Flow Heater allows for the removal of the restrictive stock heater grid plate. The new vertical coil-style heater provides the same functionality for cold starts as the stock grid heater but without obstructing airflow. Replacing the restrictive stock grid heater plate with the Banks High-Flow Intake Plate removes all obstructions and turbulence in the airflow path.How it was designedUtilizing the latest in CFD (computational fluid-dynamics), tested on the flow bench, the dyno, and on-road, Monster-Ram is a beast that only Banks could have unleashed. A direct-replacement aluminum casting, Monster-Ram is instant power, performance, and acceleration gratification. The factory inlet elbow is cramped and angular in order to accommodate the path of the stock No. 1 fuel line. Banks Engineers designed a new No. 1 fuel line, allowing the Monster-Ram to flow more air without obstruction.ExpandableWith four 1/8 inch NPT ports, perfect for temperature and pressure sensors, the sky's the limit for data acquisition.Beats the competitionLike all Banks products, the Monster-Ram was tested against all available competitors. It more than doubles the improvement over the closest competitor.This Part Fits: Year Make Model Submodel 2013-2018 Ram 2500 Big Horn 2013-2018 Ram 2500 Laramie 2014-2015 Ram 2500 Laramie Limited 2013-2018 Ram 2500 Laramie Longhorn 2016-2018 Ram 2500 Limited 2013-2015 Ram 2500 Lone Star 2013-2016 Ram 2500 Outdoorsman 2013-2018 Ram 2500 SLT 2013 Ram 2500 ST 2013-2018 Ram 2500 Tradesman 2013-2018 Ram 3500 Big Horn 2013-2018 Ram 3500 Laramie 2014-2015 Ram 3500 Laramie Limited 2013-2018 Ram 3500 Laramie Longhorn 2016-2018 Ram 3500 Limited 2013-2015,2017 Ram 3500 Lone Star 2013-2018 Ram 3500 SLT 2013 Ram 3500 ST 2013-2018 Ram 3500 Tradesman

The all new Takeda Retain Intake System produces up to 9HP and 9lbs. x ft. of torque over stock, while outflowing the factory intake by 24%. A one-piece powder-coated heat shield is used to protect the filter from unwanted hot engine air for maximum performance. Takeda intakes come complete with all necessary hardware.Installation InstructionsThis Part Fits: Year Make Model Submodel 2015-2020 Acura TLX Base 2013-2017 Honda Accord EX 2013-2017 Honda Accord EX-L 2013-2017 Honda Accord LX 2013-2017 Honda Accord LX-S 2013-2017 Honda Accord Sport 2017 Honda Accord Sport Special Edition

Gain a guaranteed increase in horsepower and torque with K&N cold air intake system featuring madrel-bent aluminum intake tube. Each system is paired with a washable, reusable High-Flow Air Filter featuring oiled cotton filter media. Some intakes are not legal for sale or use on any pollution-controlled motor vehicle in California. See the product specifications for CARB status on each part for a specific vehicle.Installation InstructionsUser 1This Part Fits: Year Make Model Submodel 2021-2022 Ford E-350 Super Duty Base

Gain a guaranteed increase in horsepower and torque with a K&N cold air intake system featuring a mandrel-bent aluminum intake tube. Each system is paired with a washable, reusable High-Flow Air Filter featuring oiled cotton filter media. The oversized, conical filter design allows you to go up to 100,000 miles between filter services under normal highway driving conditions. A custom heat shield or air box helps protect intake air from the high temperature of your engine bay, and the entire system can typically be installed in less than 90 minutes. Some intakes are not legal for sale or use on any pollution controlled motor vehicle in California. See the product specifications for CARB status on each part for a specific vehicle.Installation InstructionsUser 1This Part Fits: Year Make Model Submodel 2001 Ford Explorer Eddie Bauer 2001 Ford Explorer Limited 2001 Ford Explorer Postal 2001 Ford Explorer XL Fleet 2001 Ford Explorer XLS 2001 Ford Explorer XLT 2001-2002 Ford Explorer Sport Base 2003 Ford Explorer Sport XLS 2003 Ford Explorer Sport XLT 2001 Ford Explorer Sport Trac Base 2002 Ford Explorer Sport Trac XL 2003-2004 Ford Explorer Sport Trac XLS 2003-2004 Ford Explorer Sport Trac XLT 2001-2003 Ford Ranger Edge 2001-2003 Ford Ranger XL 2001-2003 Ford Ranger XLT 2002-2003 Mazda B4000 Base 2001-2003 Mazda B4000 DS 2001,2003 Mazda B4000 SE

Gain a guaranteed increase in horsepower and torque with a K&N cold air intake system featuring a mandrel-bent aluminum intake tube. Each system is paired with a washable, reusable High-Flow Air Filter featuring oiled cotton filter media. The oversized, conical filter design allows you to go up to 100,000 miles between filter services under normal highway driving conditions. A custom heat shield or air box helps protect intake air from the high temperature of your engine bay, and the entire system can typically be installed in less than 90 minutes. Some intakes are not legal for sale or use on any pollution controlled motor vehicle in California. See the product specifications for CARB status on each part for a specific vehicle.Installation InstructionsUser 1Installation InstructionsThis Part Fits: Year Make Model Submodel 2019-2024 Toyota RAV4 Adventure 2019-2024 Toyota RAV4 LE 2019-2024 Toyota RAV4 Limited 2020-2024 Toyota RAV4 TRD Off-Road 2019-2024 Toyota RAV4 XLE 2019-2024 Toyota RAV4 XLE Premium

Gain a guaranteed increase in horsepower and torque with K&N cold air intake system featuring madrel-bent aluminum intake tube. Each system is paired with a washable, reusable High-Flow Air Filter featuring oiled cotton filter media. Some intakes are not legal for sale or use on any pollution-controlled motor vehicle in California. See the product specifications for CARB status on each part for a specific vehicle.Installation InstructionsUser 1This Part Fits: Year Make Model Submodel 2022-2025 Hyundai Elantra N Base

The K&N Typhoon air intake system is a free-flowing, mandrel-bent aluminum tube air induction system. The restrictive factory air filter and air intake housing are replaced by the K&N Typhoon air intake which is designed to dramatically reduce air flow restriction as it smoothes and straightens air flow. This allows your engine to inhale a larger amount of air than the factory air intake. More air means more usable power and acceleration throughout the engine's RPM range. The air intake comes with a black rubber topped K&N high-flow air filter and a heat shield that installs into the previous air box space. Air is directed through the intake tube into the engine's throttle body for a guaranteed power gain. The intake tube has an attractive silver powder-coat finish that's made to last and it accommodates the factory mass air sensor and crank case vent hose. The oversized cone shaped air filter can be used for up to 100,000 miles before servicing is needed depending on driving conditions. This air intake is relatively easy to install usually in 90 minutes or less. Some Typhoon air intakes are not legal for sale or use in California and other states adopting California emission standards while others are CARB exempt and 50 state legal. Check the vehicle applications and specific CARB status for each vehicle and air intake.Installation InstructionsUser 1Installation InstructionsThis Part Fits: Year Make Model Submodel 2020 Hyundai Elantra Limited 2020 Hyundai Elantra SE 2020 Hyundai Elantra SEL 2020 Hyundai Elantra Value Edition 2019-2021 Kia Forte EX 2019-2022 Kia Forte FE 2020-2024 Kia Forte GT-Line 2023-2024 Kia Forte LX 2019-2024 Kia Forte LXS 2019 Kia Forte S

Enhance your Toyota Tundra V6 3.4L’s performance by replacing the restrictive factory intake with our advanced air intake system. Designed to boost horsepower and torque while increasing engine airflow, this unit features a high-density polyethylene (HDPE) tube and a durable, reusable high-flow air filter for lasting performance—even up to 100,000 miles under normal driving conditions—all without voiding your vehicle’s warranty.Key Features• HDPE rotationally-molded tube design for maximum airflow• Washable, reusable high-flow air filter with oiled cotton media• Custom heat shield to defend intake air from engine bay heat• Typically installs in 60 minutes using standard hand tools• Quality-backed performance and reliability• Note: For California, verify legal compliance as some intakes may not be approvedSpecifications• Material: High-density polyethylene (HDPE) tube• Filter Life: Up to 100,000 miles of highway driving• Performance Gains: Expected increases in horsepower and torque• Installation Time: Under 60 minutes with basic toolsFits These Models• 2000 Toyota Tundra (Base, SR5)• 2001 Toyota Tundra (Base, SR5)• 2002 Toyota Tundra (Base, SR5)For more detailed guidance, please refer to our Installation Instructions or check out this User Guide. Explore our full range of innovative air intake systems in our Air Intake Systems collection.

Boost your engine's performance with this advanced air intake kit, engineered to increase horsepower and torque by optimizing airflow and throttle response. Enjoy enhanced durability and efficiency with every drive.Key Features• An enclosed air box design shields the filter and incoming air from engine bay heat while offering quick, tool-free access for maintenance.• A high-density polyethylene (HDPE) rotationally molded tube notably boosts airflow volume for superior performance.• A washable, reusable high-flow air filter featuring premium oiled-cotton media provides reliable air filtration.• An oversized, conical design extends the service interval up to 100,000 miles under normal highway conditions.Easy InstallationThis intake kit can be installed in less than 60 minutes, making it a hassle-free upgrade for your vehicle. For detailed installation instructions, please refer to our Installation Instructions.Compatibility & Legal InfoDesigned for select 2017–2019 Chevrolet Silverado and GMC Sierra models, please check our dedicated fitment tool for complete vehicle compatibility. Note that some intakes may not be legal for sale or use on any pollution-controlled motor vehicles in California.For more performance upgrades, explore our Air Intake Systems collection.

Discover the K&N 57-3098 FIPK Air Intake System designed to boost the performance of your 2017–2019 Chevrolet Silverado V8 5.3L. This innovative system replaces restrictive factory components while retaining the original air box, ensuring improved airflow, increased horsepower, and better throttle response. With its advanced design, it maximizes efficiency and delivers a distinctive engine sound every time you drive.Key Benefits• Increased horsepower and torque with smoother, direct airflow• Enhanced throttle response and a more aggressive engine note• Extended high-flow air filter lifespan – up to 50,000 miles before servicing• Quick, tool-friendly installation that typically takes about 90 minutes• Backed by K&N’s No-Hassle Lifetime Limited WarrantyTechnical Information• Compatibility: Engineered for select Chevrolet Silverado models and also fits various Cadillac and GMC vehicles.• Construction: Features an aerodynamically engineered intake tube and a premium high-flow air filter for superb performance.• Installation: Designed to be installed with common tools such as a screwdriver, ratchet, and Allen wrench in roughly 90 minutes.• Regulatory: Complies with applicable emissions standards; please verify local state regulations for legal use.Fits• 2017–2020 Cadillac Escalade (Base, Luxury, Platinum, Premium Luxury)• 2017–2018 Chevrolet Silverado 1500 (Custom, High Country, LS, LT, LTZ, SSV, WT)• 2019 Chevrolet Silverado 1500 LD (Custom, LT, WT)• 2017–2020 Chevrolet Suburban and Tahoe• 2017–2018 and 2019 GMC Sierra, Yukon, and Yukon XLFor detailed fitment information, please visit our Air Intake Systems collection.

Experience an impressive boost in performance with this high-performance intake kit designed for the 2016–2017 Cadillac ATS-V. Engineered to enhance your engine’s efficiency, this kit increases airflow to deliver quicker throttle response, a more aggressive engine sound, and an overall improvement in horsepower and torque.Key Features• High-density polyethylene (HDPE) roto-molded intake tube optimized for maximum airflow• Washable, reusable high-flow air filter featuring premium oiled cotton media that lasts up to 100,000 miles under typical highway conditions• Custom-engineered heat shield that safeguards intake air from high engine bay temperatures• Quick installation—most users complete installation in under 60 minutes• Precision fitment engineered exclusively for the 2016–2017 Cadillac ATS-V• Note: Some intakes may not be legal for sale or use on pollution-controlled vehicles in California; check the CARB status for your vehicleInstallation ProcessInstallation is straightforward with basic hand tools. For complete instructions, please review our Installation Instructions and accompanying User Guide.Why Choose This Kit?Upgrade your vehicle with confidence. Enjoy enhanced performance over standard OEM systems, improved durability, and superior airflow that elevates your driving experience. If you’re ready for a premium performance upgrade, this intake kit is engineered to meet your high standards.Elevate your ATS-V and discover additional performance solutions in our Air Intake Systems collection. Purchase now and experience the difference on every drive!

Leveraging nearly 30 years of airflow engineering experience, CORSA(R) Air Intakes are the perfect compliment to a CORSA Performance(R) exhaust system. Each CORSA(R) air intake has been custom designed by CORSA's engineers to optimize performance by increasing airflow. Paired with CORSA's MaxFlow 5(TM), 5 layer oiled cotton gauze air filter, CORSA(R) air intakes outflow stock air intakes increasing engine efficiency and increasing performance. Every MaxFlow 5(TM), 5 layer oiled cotton gauze air filter features high quality textiles, pleated between a top and bottom aluminum screen designed to filter out damaging particulates while protecting your engine. MaxFlow 5(TM) reusable oiled filters offer extended maintenance intervals (up to 40K miles depending on driving conditions). Whether On-Road or Off, CORSA Performance(R) has you covered.This Part Fits: Year Make Model Submodel 2021-2023 Ford F-150 King Ranch 2021-2023 Ford F-150 Lariat 2021-2023 Ford F-150 Platinum 2021-2023 Ford F-150 SSV 2023 Ford F-150 Tremor 2021-2023 Ford F-150 XL 2021-2023 Ford F-150 XLT

Upgrade your fleet vehicles and protect your investment from grid heater bolt failure. Don't let the stock elbow and heater kill performance or your engine. Get back all that power you lose with 88.3 percent greater Mass Air Flow for a more responsive, reliable, power-efficient engine. What it doesThe Monster-Ram improves airflow from the intercooler. It flows 72.7 lbs/min MAF (Mass Air Flow) with Bank's High-Flow Heater and Billet Intake Plate compared to stock's 38.6 lbs/min MAF.Monster-Ram raises boost without increasing backpressure at the turbine. The result is a more responsive, power-efficient engine that offers even more headroom than stock for higher horsepower applications.The complete systemBanks' High-Flow Heater and Billet Intake Plate complete the perfect system. The High-Flow Heater allows for the removal of the restrictive stock heater grid plate. The new vertical coil-style heater provides the same functionality for cold starts as the stock grid heater but without obstructing airflow. Replacing the restrictive stock grid heater plate with the Banks High-Flow Intake Plate removes all obstructions and turbulence in the airflow path.How it was designedUtilizing the latest in CFD (computational fluid-dynamics), tested on the flow bench, the dyno, and on-road, Monster-Ram is a beast that only Banks could have unleashed. A direct-replacement aluminum casting, Monster-Ram is instant power, performance, and acceleration gratification. The factory inlet elbow is cramped and angular in order to accommodate the path of the stock No.1 fuel line. Banks Engineers designed a new No.1 fuel line, allowing the Monster-Ram to flow more air without obstruction.ExpandableWith four 1/8 inch NPT ports, perfect for temperature and pressure sensors, the sky's the limit for data acquisition.Beats the competitionLike all Banks products, the Monster-Ram was tested against all available competitors. It more than doubles the improvement over the closest competitor.This Part Fits: Year Make Model Submodel 2019-2024 Ram 3500 Big Horn 2019-2024 Ram 3500 Laramie 2019-2020 Ram 3500 Laramie Longhorn 2019-2024 Ram 3500 Limited 2021-2024 Ram 3500 Limited Longhorn 2019-2022 Ram 3500 Lone Star 2019-2024 Ram 3500 SLT 2024 Ram 3500 Special Service 2019-2024 Ram 3500 Tradesman

The Banks Monster-Ram is the best-engineered intake elbow (horn) available for the 2019-2024 RAM Cummins 6.7L. Gain responsiveness and power efficiency. Improve Mass Air Flow by 88 percent over the stock intake. Prevents grid heater bolt failure. What it doesThe Monster-Ram improves airflow from the intercooler. It flows 72.7 lbs/min MAF (Mass Air Flow) with Bank's High-Flow Heater and Billet Intake Plate compared to stock's 38.6 lbs/min MAF.Monster-Ram raises boost without increasing backpressure at the turbine. The result is a more responsive, power-efficient engine that offers even more headroom than stock for higher horsepower applications.The complete systemBanks' High-Flow Heater and Billet Intake Plate complete the perfect system. The High-Flow Heater allows for the removal of the restrictive stock heater grid plate. The new vertical coil-style heater provides the same functionality for cold starts as the stock grid heater but without obstructing airflow. Replacing the restrictive stock grid heater plate with the Banks High-Flow Intake Plate removes all obstructions and turbulence in the airflow path.How it was designedUtilizing the latest in CFD (computational fluid-dynamics), tested on the flow bench, the dyno, and on-road, Monster-Ram is a beast that only Banks could have unleashed. A direct-replacement aluminum casting, Monster-Ram is instant power, performance, and acceleration gratification. The factory inlet elbow is cramped and angular in order to accommodate the path of the stock No. 1 fuel line. Banks Engineers designed a new No. 1 fuel line, allowing the Monster-Ram to flow more air without obstruction.ExpandableWith four 1/8 inch NPT ports, perfect for temperature and pressure sensors, the sky's the limit for data acquisition.Beats the competitionLike all Banks products, the Monster-Ram was tested against all available competitors. It more than doubles the improvement over the closest competitor.This Part Fits: Year Make Model Submodel 2019-2024 Ram 2500 Big Horn 2019-2024 Ram 2500 Laramie 2019-2021 Ram 2500 Laramie Longhorn 2019-2024 Ram 2500 Limited 2021-2024 Ram 2500 Limited Longhorn 2019-2024 Ram 2500 Lone Star 2023-2024 Ram 2500 Rebel 2024 Ram 2500 Special Service 2019-2024 Ram 2500 Tradesman 2019-2024 Ram 3500 Big Horn 2019-2024 Ram 3500 Laramie 2019-2020 Ram 3500 Laramie Longhorn 2019-2024 Ram 3500 Limited 2021-2024 Ram 3500 Limited Longhorn 2019-2022 Ram 3500 Lone Star 2019-2024 Ram 3500 SLT 2024 Ram 3500 Special Service 2019-2024 Ram 3500 Tradesman

The Banks Monster-Ram is the best-engineered intake elbow (horn) available for the 2013-2018 RAM Cummins 6.7L. Gain responsiveness and power efficiency. Improve Mass Air Flow by 88 percent over the stock intake. Prevents grid heater bolt failure. What it doesThe Monster-Ram improves airflow from the intercooler. It flows 72.7 lbs/min MAF (Mass Air Flow) with Banks' High-Flow Heater and Billet Intake Plate compared to stock's 38.6 lbs/min MAF.Monster-Ram raises boost without increasing backpressure at the turbine. The result is a more responsive, power-efficient engine that offers even more headroom than stock for higher horsepower applications.The complete systemBank's High-Flow Heater and Billet Intake Plate complete the perfect system. The High-Flow Heater allows for the removal of the restrictive stock heater grid plate. The new vertical coil-style heater provides the same functionality for cold starts as the stock grid heater but without obstructing airflow. Replacing the restrictive stock grid heater plate with the Banks High-Flow Intake Plate removes all obstructions and turbulence in the airflow path.How it was designedUtilizing the latest in CFD (computational fluid-dynamics), tested on the flow bench, the dyno, and on-road, Monster-Ram is a beast that only Banks could have unleashed. A direct-replacement aluminum casting, Monster-Ram is instant power, performance, and acceleration gratification. The factory inlet elbow is cramped and angular in order to accommodate the path of the stock No. 1 fuel line. Banks Engineers designed a new No. 1 fuel line, allowing the Monster-Ram to flow more air without obstruction.ExpandableWith four 1/8 inch NPT ports, perfect for temperature and pressure sensors, the sky's the limit for data acquisition.Beats the competitionLike all Banks products, the Monster-Ram was tested against all available competitors. It more than doubles the improvement over the closest competitor.This Part Fits: Year Make Model Submodel 2013-2018 Ram 2500 Big Horn 2013-2018 Ram 2500 Laramie 2014-2015 Ram 2500 Laramie Limited 2013-2018 Ram 2500 Laramie Longhorn 2016-2018 Ram 2500 Limited 2013-2015 Ram 2500 Lone Star 2013-2016 Ram 2500 Outdoorsman 2013-2018 Ram 2500 SLT 2013 Ram 2500 ST 2013-2018 Ram 2500 Tradesman 2013-2018 Ram 3500 Big Horn 2013-2018 Ram 3500 Laramie 2014-2015 Ram 3500 Laramie Limited 2013-2018 Ram 3500 Laramie Longhorn 2016-2018 Ram 3500 Limited 2013-2015,2017 Ram 3500 Lone Star 2013-2018 Ram 3500 SLT 2013 Ram 3500 ST 2013-2018 Ram 3500 Tradesman

The Banks Monster-Ram is the best-engineered intake elbow (horn) available for the 2007-2012 RAM Cummins 6.7L. Gain responsiveness and power efficiency. Improve Mass Air Flow by 88 percent over the stock intake. Prevents grid heater bolt failure. What it doesThe Monster-Ram improves airflow from the intercooler. It flows 72.7 lbs/min MAF (Mass Air Flow) with Bank's High-Flow Heater and Billet Intake Plate compared to stock's 38.6 lbs/min MAF.Monster-Ram raises boost without increasing backpressure at the turbine. The result is a more responsive, power-efficient engine that offers even more headroom than stock for higher horsepower applications.The complete systemBank's High-Flow Heater and Billet Intake Plate complete the perfect system. The High-Flow Heater allows for the removal of the restrictive stock heater grid plate. The new vertical coil-style heater provides the same functionality for cold starts as the stock grid heater but without obstructing airflow. Replacing the restrictive stock grid heater plate with the Banks High-Flow Intake Plate removes all obstructions and turbulence in the airflow path.How it was designedUtilizing the latest in CFD (computational fluid-dynamics), tested on the flow bench, the dyno, and on-road, Monster-Ram is a beast that only Banks could have unleashed. A direct-replacement aluminum casting, Monster-Ram is instant power, performance, and acceleration gratification. The factory inlet elbow is cramped and angular in order to accommodate the path of the stock No. 1 fuel line. Banks Engineers designed a new No. 1 fuel line, allowing the Monster-Ram to flow more air without obstruction.ExpandableWith four 1/8 inch NPT ports, perfect for temperature and pressure sensors, the sky's the limit for data acquisition.Beats the competitionLike all Banks products, the Monster-Ram was tested against all available competitors. It more than doubles the improvement over the closest competitor.This Part Fits: Year Make Model Submodel 2007-2010 Dodge Ram 2500 Laramie 2007-2010 Dodge Ram 2500 SLT 2007-2010 Dodge Ram 2500 ST 2008-2010 Dodge Ram 2500 SXT 2010 Dodge Ram 2500 TRX 2007-2010 Dodge Ram 3500 Laramie 2007-2010 Dodge Ram 3500 SLT 2007 Dodge Ram 3500 Sport 2007-2010 Dodge Ram 3500 ST 2008-2009 Dodge Ram 3500 SXT 2011-2012 Ram 2500 Laramie 2011-2012 Ram 2500 Laramie Longhorn 2012 Ram 2500 Outdoorsman 2011-2012 Ram 2500 SLT 2011-2012 Ram 2500 ST 2011-2012 Ram 3500 Laramie 2011-2012 Ram 3500 Laramie Longhorn 2011-2012 Ram 3500 SLT 2011-2012 Ram 3500 ST

Volant Performance Air Intake Systems are designed for one thing, Performance. By optimizing airflow and utilizing free-flowing filters, Volant Performance Intakes outflow stock systems to increase overall performance while protecting your engine. This intake features Volant's high performance MaxFlow 5, 5 layer oiled cotton gauze air filters are made of the highest quality textiles, pleated between a top and bottom aluminum screen. Each filter comes pre-oiled and ready for use. This filter is specifically designed to allow the highest air flow rate possible for maximum power gains but deliver a very long filter life and maintenance intervals (up to 40K miles depending on driving conditions). Whether On-Road or Off, Volant Performance has you covered.Technical BulletinInstallation InstructionsThis Part Fits: Year Make Model Submodel 2009-2012 Chevrolet Colorado LT 2009-2012 GMC Canyon SLE 2009-2012 GMC Canyon SLT

The K&N Drycharger is a silicone treated, polyester wrap that is made to cover K&N Air Filters or Personal Watercraft Flame Arrestors. These Drychargers, which are similar to the K&N Prechargers, contain uniform micron sized openings that allow high air flow. Yet, due to the Drychargers silicone treated polyester wrap, the amount of water that reaches the air filter or flame arrestor is limited.

The CORSA Performance C8 Z06 Corvette dual air intake is made from multi-layer 100% carbon fiber construction and pairs aesthetics and engineering for maximum strength and performance. Compared to stock; the optimized shape of the CORSA Performance C8 Z06 air intake tubes, improved airbox design, combined with high-performance filtration, increases overall performance and fuel economy. Dyno tuned for maximum results, the CORSA Performance C8 Carbon Fiber Air intake produces up to an additional 33HP @4950RPM and 35 FT LBS TQ @4875RPM with gains accelerating starting at 6400RPM from the LT-2 engine without a tune. The C8 Z06 intake comes available exclusively in DryTech Filtration to ensure reduced maintenance intervals, up to 50K miles, depending on driving conditions. The Corsa Performance C8 Z06 carbon fiber Intake is backed by a Limited Lifetime Warranty to the original purchaser.*Filters are backed by a 1 year warranty.This Part Fits: Year Make Model Submodel 2023-2025 Chevrolet Corvette Z06

Maximum performance within minutes is what this aFe Stage 1 cold air intake system delivers. Enclosed in a durable 16 gauge heat shield; a massive washable/reusable; 360 deg. conical Pro 5R air filter increases airflow resulting in an additional 6 hp; and 7 lbs./ft/ torque. This intake system also features a unique 3-angle adaptor for increased air velocity. The Pro 5R air filter is constructed with 100 percent polyurethane for long life and multiple cleaning cycles. This intake is the easiest intake on the market to install. Simply remove the factory intake and mount the 3-angle adaptor with the air filter to the MAF sensor tube and you are breathing more air and producing more power.Installation InstructionsThis Part Fits: Year Make Model Submodel 2003-2005 Ford Excursion Eddie Bauer 2000-2005 Ford Excursion Limited 2004-2005 Ford Excursion XLS 2000-2005 Ford Excursion XLT 1999 Ford F-250 Base 1999 Ford F-250 Lariat 1999 Ford F-250 XL 1999 Ford F-250 XLT 2004 Ford F-250 Super Duty Harley-Davidson Edition 2004 Ford F-250 Super Duty King Ranch 1999-2004 Ford F-250 Super Duty Lariat 1999-2004 Ford F-250 Super Duty XL 1999-2004 Ford F-250 Super Duty XLT 2004 Ford F-350 Super Duty Harley-Davidson Edition 2003-2004 Ford F-350 Super Duty King Ranch 1999-2004 Ford F-350 Super Duty Lariat 1999-2004 Ford F-350 Super Duty XL 1999-2004 Ford F-350 Super Duty XLT 2000-2004 Ford F-450 Super Duty Lariat 2000-2004 Ford F-450 Super Duty XL 2000-2004 Ford F-450 Super Duty XLT 2001-2004 Ford F-550 Super Duty Lariat 2001-2004 Ford F-550 Super Duty XL 2001-2004 Ford F-550 Super Duty XLT

Unique Computer Design Carbon Fiber Housing W/ Sight Window: The simple yet elegant design of the one-piece sealed housing makes installation a snap and features our patent pending filter-to-housing interface. A large clear sight window allows for filter inspection without removal of the air box. The housing is made out of lightweight high gloss, clear-coated plain weave carbon fiber and mounts directly into the factory location on the fender well to capture the coolest air available from the factory intake tract. Lightweight high gloss clear-coated plain weave carbon fiber tube to achieve maximum power gains while maintaining a perfect fit. This tube has a built-in resonance chamber to catch un-wanted air intake noises. Two billet aluminum fittings are mounted on the tube to provide a perfect connection with the factory vacuum line. This Momentum intake system was designed around the largest filter possible to allow maximum performance and filtration. This cone filter has a massive 7" oval flange and is 8-1/2" tall Pro DRY S filter media. The Pro DRY S performance air filter features 3-layers of progressively finer mesh synthetic "oil-free" media and is constructed with 100% polyurethane frame for long life and multiple cleaning cycles. Large 5-Layer Performance Air Filter: This Momentum intake system was designed around the largest filter possible to allow maximum performance and filtration. This cone filter has a massive 7" oval flange and is 8-1/2" tall Pro 5R filter media. The Pro 5R performance air filter features 5-layers of progressively finer mesh cotton gauze oiled media and is constructed with 100% polyurethane frame for long life and multiple cleaning cycles. Also included in the kit is a Black Series serialized plate to assure the authenticity of the intake. Premium stainless steel T-bolt clamps and a silicone hump coupler are used for strength and durability while also providing the most secure installation available.Installation InstructionsThis Part Fits: Year Make Model Submodel 2017-2019 Chevrolet Corvette Grand Sport 2014-2019 Chevrolet Corvette Stingray 2015-2019 Chevrolet Corvette Z06 2019 Chevrolet Corvette ZR1

This aFe POWER Pro 5R air filter is a 7” tall, pre-oiled, 360-degree radial flow performance air filter with five layers of progressively finer cotton gauze media for maximum performance. It provides your engine with the largest amount of high-flowing air, usually resulting in the highest power gains out of all our filter media options. This media is perfect for street and/or track use. One piece 3 IN mandrel-bent wrinkle-black powder-coated aluminum intake tube directs unrestricted airflow from the massive filter to the turbo for more horsepower and torque. aFe developed this sturdy 18 gauge steel wrinkle-black powder-coated heat shield to mount onto the top of the lower half of the factory airbox to provide a hassle-free installation utilizing factory mounting locations. Premium hardware and clamps are used to securely mount the high flow air filter and the intake tube.Installation InstructionsThis Part Fits: Year Make Model Submodel 2015-2020 Audi A3 Premium 2015-2020 Audi A3 Premium Plus 2015-2019 Audi A3 Prestige 2019 Audi A3 Titanium 2015-2020 Audi A3 Quattro Premium 2015-2020 Audi A3 Quattro Premium Plus 2015-2019 Audi A3 Quattro Prestige 2020 Audi S3 Premium 2015-2020 Audi S3 Premium Plus 2015-2019 Audi S3 Prestige 2016 Volkswagen Golf Base 2015 Volkswagen Golf Launch Edition 2015-2018 Volkswagen Golf S 2015-2016,2018 Volkswagen Golf SE 2015-2016 Volkswagen Golf SEL 2017 Volkswagen Golf Wolfsburg Edition 2015-2019 Volkswagen Golf R Base 2015-2021 Volkswagen GTI Autobahn 2019 Volkswagen GTI Rabbit Edition 2015-2021 Volkswagen GTI S 2015-2021 Volkswagen GTI SE 2017 Volkswagen GTI Sport