Spray Vehicle Interior cleaner onto the parts and surfaces to be cleaned or apply using a damp sponge or cloth. Allow to take effect according to the degree of contamination but do not allow to dry out. Next, rub in and then rub dry with a clean damp cloth. Repeat treatment if contamination persists.Product Specifications SheetProduct Specifications Sheet

LIQUI MOLY 400mL Pro-Line Injector & Glow Plug Dismantling Aid

To prepare, attach tube with nozzle. To gain access, remove hose or pipe immediately before throttle housing. The engine needs to run to perform cleaning. If unable to start engine, disconnect air mass sensor connector while the ignition switch is in off position. Maintain minimum engine speed of 2000 rpm while spraying cleaner in short intervals of 2-3 seconds, and at the same time move the nozzle back and forth across opening to completely treat intake tract. If engine speed fluctuates more than 1000 rpm stop spraying immediately and wait for speed to stabilize. Keep cleaning fluid from contacting air mass meter or painted surfaces. If excess deposits inside EGR valve, intake manifold or intake valves, a second can of cleaner may be used to improve the result. After completion, leave the engine running at 2000 rpm for a minimum 20 seconds to allow complete removal of any residing fluid in intake system. Afterwards erase any stored fault codes.Product Specifications SheetProduct Specifications Sheet

Can contents (300 ml) are sufficient for up to5 liters (5.28 U.S. QT)of motor oil. After adding to the motor oil, allow the engine to run warm. The product can be added at any time. Minimum oil filling of 3 liters (3.17 U.S. QT) is requested for optimum product performance.Product Specifications SheetProduct Specifications Sheet

Add contents to the cooling water. Turn the heating to maximum and let the engine run on idle for 10 - 30 minutes depending on the degree of contamination. Drain the coolant and flush the cooling system with water. Fill the cooling system according to the manufacturers instructions. The content is sufficient for 10 liters (2.6 gal.)of water, a minimum of 4 liters (1 gal.) is required for optimum product performance.Product Specifications SheetProduct Specifications Sheet

Contents sufficient for max. 5 liters (5.28 U.S. QT) of motor oil, minimum filling of 3 liters (3.17 U.S QT) is requested for optimum product performance. The product is self mixing and can be added at any time, sealing first takes effect after about 600-800 km (400-500 miles). The use of Motor Oil Saver every around 30.000 Km (20.000 miles) is recommended to guarantee a lasting effect.Product Specifications SheetProduct Specifications Sheet

One 300 ml can is sufficient for up to 75 liters (20 gal.) of fuel. Regular use keeps injection system in perfect working order and gives lowest exhaust emissions. Smoother idling, better throttle response. Injection Cleaner can be mixed with fuel at any time since mixing is spontaneous. Minimum fuel filling of 25 liters (7 gal.) is requested for optimum product performance.Product Specifications SheetProduct Specifications SheetInstallation Instructions

High-tech anti-wear additive, suitable for most 4-stroke engines as well as manual transmissions and compressors.Reduces friction and wear thanks to a unique combination of ceramic compounds and chemical anti-wear agents. It will prevent direct metal-to-metal contact and reduce friction to increase engine life and reduce fuel consumption in gasoline and diesel engines.Product Specifications SheetProduct Specifications SheetInstallation InstructionsMaterial Safety Data Sheet

High-tech fuel additive, developed specifically for improved throttle response under partial engine load. Optimizes fuel atomization and combustion, cleans fuel system while providing maximum engine performance and efficiency.Product Specifications SheetProduct Specifications Sheet

Will immediately seal small leaks caused by external damage, porous solder joints and hairline cracks in cooling systems of all water cooled engines. Coolant is prevented from entering the combustion chamber due to internal leaks from head gasket etc. It does not react with oxygen or heat and will never prevent system flow or cause overheating. Radiator Stop Leak works as long as its in the coolant.Product Specifications SheetProduct Specifications Sheet

If required, clean the leather surfaces to be treated and let dry. Shake Leather Care vigorously before use. Next, pour onto a soft cloth or rag and, using circular motions, apply thinly and uniformly under light pressure. Polish off after briefly allowing it to work. Regular application will result in the optimum care and appearance. Not suitable for suede. Before application on the entire area, we suggest that you check Leather Care for compatibility with the material on a hidden area.Product Specifications SheetProduct Specifications SheetInstallation Instructions

A combination of agents, developed specifically for late model hybrid engines. Removes deposits in the fuel system and protects against corrosion. Stabilizes the fuel and protects against aging and oxidation. Diminished fuel degradation allows better engine performance and efficiency.Product Specifications SheetProduct Specifications Sheet

For best results and long-term effect add DPF protector exery 2.000 km (1.200 miles). One 300 ml can is sufficient for 75 liters (20 gal.) of Diesel. Minimum fuel filling of50 liters (14 gal.) is requested for optimum product performance.Product Specifications SheetProduct Specifications Sheet

Wash the vehicle thoroughly before application. Shakewell before use.Use a cloth or sponge to apply and work into the affected area while using light pressure (polish with a foam buffing machine at 1,500 to 2,000 rpm). Use caution near body panel edges, as the product is extremely abrasive. Wipe off any polish residue using a clean cloth (preferably a microfibre cloth).Product Specifications SheetProduct Specifications Sheet

Spray components before installing them. If the contacts are heavily corroded, allow the product to act for longer and rub off corrosion residues with a cloth or brush. Note: After spraying on, allow a flash-off period of 10 min. before connecting the component to a power supply.Product Specifications SheetProduct Specifications SheetInstallation Instructions

Cleaning is made with the compressed air gun for DPF (part no. 7946) and the specially developed DPF-Probe with 5 interchangeable tips (part no. 7945) or the DPF spray Probe long (part no. 20630). The diesel particle filter must be accessed depending on the vehicle type. In order to do this, the temperature or pressure sensor on the diesel particle filter must be removed on most vehicles. Observe: When cleaning, the particle filter's temperature should be below 40C (104F). On some vehicles the diesel particle filter is located near to the exhaust manifold or, optionally, the turbocharger, and not on the vehicle underbody. For safety reasons, utmost care must be taken when cleaning such vehicles - cleaning or flushing liquid may otherwise enter the combustion chamber through an open exhaust valve. The appropriate Pro-Line spray probe for the vehicle type is then fed into the particle filter through the opening. The full container of Pro-Line cleaner for diesel particle filters (1 liter) is sprayed directly onto the surface of the particle filter in intervals of 5 to 10 seconds (each with a break of 5 to 10 seconds in between) at an operating pressure of 6 to 8 bar. The probe must be rotated and moved back and forth during cleaning in order to cover as much of the filter surface with Pro-Line cleaner. The particle filter is then flushed with the full container of Pro-Line flushing liquid for diesel particle filters (500 ml). The compressed air gun for DPF (part no. 7946) is also used here at the same intervals as during the cleaning process. The particulate deposits are dissolved during the cleaning process and distributed around the diesel particle filter, where they can then be burned off as part of normal regeneration. After reinstalling the sensor, the service centre or workshop must trigger regeneration according to the manufacturers' instruction. Caution: The protective measures for safe handling can be found in the safety data sheet.Product Specifications SheetProduct Specifications SheetInstallation Instructions

For all gasoline engines. Suitable for standard and high-octane gas, leaded and unleaded. 150 ml is sufficient for up to 75 liters (20 gal.)of fuel.Minimum fuel filling of 25 liters (7 gal.) is requested for optimum product performance.Product Specifications SheetProduct Specifications SheetInstallation Instructions

LIQUI MOLY 10g Screw Retainer - Medium Strength

LIQUI MOLY 10g Screw Retainer - High Strength

DeatschWerks 101S Street Octane Booster 32oz. Cans - Case of 8Hazardous Materials Info SheetProduct Specifications Sheet