For those running high HP applications that depend on the water-methanol for tuning Snow Performance offers direct port water-meth upgrades to directly mount a nozzle into each cylinder. Comes with 2 4CYL distribution block, 2high flow solenoids, and all plumbing to install a nozzle in each cylinder. NOTE: Nozzles not included and must be purchased separately.

Snow Performance Water-Methanol Injection systems provide increased performance with or without nitrous. Water Methanol Injection cools your incoming air charge and increases the total octane effect of pump gas. This allows you to run increased timing which results in increased power and torque. When used with Nitrous, the need for timing retard is greatly reduced or eliminated. Boosted applications especially benefit from reduced intake temperatures. NX Water / Methanol systems include the latest technology and the highest quality components available. This innovative plate combines the performance and safety benefits of Water Methanol injection with the horsepower and throttle response improvements of a carburetor shear plate. This design places the water methanol nozzle in the center of the Carb bores for excellent cylinder to cylinder distribution. The system includes a high output water methanol pump, a 3 quart tank, filtered nozzles, push lock line as well as everything needed for the installation. Fits on Dominator or 4500 series intake flanges. Stage 2 systems are activated by a two dial electronic controller that progressively controls water methanol output by either boost or vacuum.

Snow Performance Water-Methanol Injection systems provide increased performance with or without nitrous. Water Methanol Injection cools your incoming air charge and increases the total octane effect of pump gas. This allows you to run increased timing which results in increased power and torque. When used with Nitrous, the need for timing retard is greatly reduced or eliminated. Boosted applications especially benefit from reduced intake temperatures. NX Water / Methanol systems include the latest technology and the highest quality components available. This innovative plate combines the performance and safety benefits of Water Methanol injection with the horsepower and throttle response improvements of a carburetor shear plate. This design places the water methanol nozzle in the center of the Carb bores for excellent cylinder to cylinder distribution. The system includes a high output water methanol pump, a 3 quart tank, filtered nozzles, push lock line as well as everything needed for the installation. Fits on Dominator or 4500 series intake flanges. Stage 2 systems are activated by a two dial electronic controller that progressively controls water methanol output by either boost or vacuum.

Snow Performance Water-Methanol Injection systems provide increased performance with or without nitrous. Water Methanol Injection cools your incoming air charge and increases the total octane effect of pump gas. This allows you to run increased timing which results in increased power and torque. When used with Nitrous, the need for timing retard is greatly reduced or eliminated. Boosted applications especially benefit from reduced intake temperatures. NX Water / Methanol systems include the latest technology and the highest quality components available. This innovative plate combines the performance and safety benefits of Water Methanol injection with the horsepower and throttle response improvements of a carburetor shear plate. This design places the water methanol nozzle in the center of the Carb bores for excellent cylinder to cylinder distribution. The system includes a high output water methanol pump, a 3 quart tank, filtered nozzles, push lock line as well as everything needed for the installation. Fits on Dominator or 4500 series intake flanges. Stage 2 systems are activated by a two dial electronic controller that progressively controls water methanol output by either boost or vacuum.

Snow Performance Water-Methanol Injection systems provide increased performance with or without nitrous. Water Methanol Injection cools your incoming air charge and increases the total octane effect of pump gas. This allows you to run increased timing which results in increased power and torque. When used with Nitrous, the need for timing retard is greatly reduced or eliminated. Boosted applications especially benefit from reduced intake temperatures. NX Water / Methanol systems include the latest technology and the highest quality components available. This innovative plate combines the performance and safety benefits of Water Methanol injection with the horsepower and throttle response improvements of a carburetor shear plate. This design places the water methanol nozzle in the center of the Carb bores for excellent cylinder to cylinder distribution. The system includes a high output water methanol pump, a 3 quart tank, filtered nozzles, push lock line as well as everything needed for the installation. Fits on Dominator or 4500 series intake flanges. Stage 2 systems are activated by a two dial electronic controller that progressively controls water methanol output by either boost or vacuum.

Run 11:1 to 13:1 compression ratio (or more) on pump gas!! Increase your pump gas octane by 20-25 points and make more power. More power and efficiency with cooler running for your naturally aspirated V8 Muscle Car. This system uses a wide open throttle switch to activate the Water/Methanol only under full load. High compression modified engines can gain performance through cooler intake charges and the large increase in octane and detonation suppression. This system allows you to save money by using lower grades of gasoline. Comes with one 4150-style Carburetor spacer plate threaded for 1/8" injection nozzles, and a solenoid to prevent vacuum siphoning. System includes: SHO (Special High Output) Pump 1" Carb Spacer Plate Solenoid Valve to prevent Siphoning 3 Quart Reservoir WOT (Wide Open Throttle) switch 2 nozzles cover a Wide Range of Horsepower All Required Hardware Needed For Installation Comprehensive Instructions,

Run 11:1 to 13:1 compression ratio (or more) on pump gas!! Increase your pump gas octane by 20-25 points and make more power. More power and efficiency with cooler running for your naturally aspirated V8 Muscle Car. This system uses a wide open throttle switch to activate the Water/Methanol only under full load. High compression modified engines can gain performance through cooler intake charges and the large increase in octane and detonation suppression. This system allows you to save money by using lower grades of gasoline. Comes with one 4150-style Carburetor spacer plate threaded for 1/8" injection nozzles, and a solenoid to prevent vacuum siphoning. System includes: SHO (Special High Output) Pump 1" Carb Spacer Plate Solenoid Valve to prevent Siphoning 3 Quart Reservoir WOT (Wide Open Throttle) switch 2 nozzles cover a Wide Range of Horsepower All Required Hardware Needed For Installation Comprehensive Instructions,

For those running high HP applications that depend on the water-methanol for tuning Snow Performance offers direct port water-meth upgrades to directly mount a nozzle into each cylinder. Comes with 2 4CYL distribution block, 2high flow solenoids, and all plumbing to install a nozzle in each cylinder. NOTE: Nozzles not included and must be purchased separately.

For those running high HP applications that depend on the water-methanol for tuning Snow Performance offers direct port water-meth upgrades to directly mount a nozzle into each cylinder. Comes with 2 4CYL distribution block, 2high flow solenoids, and all plumbing to install a nozzle in each cylinder. NOTE: Nozzles not included and must be purchased separately.

Are you tired of multi-pump fuel upgrades that require a bunch of T-fittings, unreliable hoses and hose clamps?Snow Performance has the solution! The Snow Performance Multi-Pump Fuel Hats feature a billet aluminum manifold with CNC machined passages making these the nicest high output fuel pump upgrade on the market! This design eliminates the need for hose clamps and rubber or plastic lines that can deteriorate and cause problems. No detail has been overlooked with these assemblies. The CNC machined bodies hold the fuel pumps securely and feature Viton chemical-resistant O-rings and guarantee a perfect leak-free fit.Snow Performance Fuel Hats are engineered, CNC machined, and built in the USA from 6061 billet aluminum. These billet hats receive a black anodized finish for the ultimate durability and corrosion resistance, making them compatible with E85 and other harsh fuels. Snow fuel hats completely replace your factory fuel hat/bucket for an easy installation, retaining your factory tank features including, the OE fuel level sending unit, EVAP system, filler neck, and if equipped with saddle style tanks, the fuel transfer pump functionality. Snow fuel hats feature female 10AN ORB feed and 8AN ORB return ports. 90 degree swivel adapter fittings are sold separately to adapt to your desired combination of 10AN, 8AN or 6AN lines. To meet your specific vehicle's fuel demands, these pump assemblies are configurable with a combination of 2 or 3 fuel pumps. No knock-off pumps here. Get OE reliability with genuine TI Automotive (Walbro) fuel pumps in your choice of flow rates (450LPH or 470LPH).These fuel pumps are designed for a return-style installation only. Do not attempt to run these pumps in a returnless application. These pumps are compatible with 100% Gasoline, 100% Ethanol or any blend of Gasoline and Ethanol (E10, E85, E98 for example). These pumps are NOT compatible with methanol.

Are you tired of multi-pump fuel upgrades that require a bunch of T-fittings, unreliable hoses and hose clamps?Snow Performance has the solution! The Snow Performance Multi-Pump Fuel Hats feature a billet aluminum manifold with CNC machined passages making these the nicest high output fuel pump upgrade on the market! This design eliminates the need for hose clamps and rubber or plastic lines that can deteriorate and cause problems. No detail has been overlooked with these assemblies. The CNC machined bodies hold the fuel pumps securely and feature Viton chemical-resistant O-rings and guarantee a perfect leak-free fit.Snow Performance Fuel Hats are engineered, CNC machined, and built in the USA from 6061 billet aluminum. These billet hats receive a black anodized finish for the ultimate durability and corrosion resistance, making them compatible with E85 and other harsh fuels. Snow fuel hats completely replace your factory fuel hat/bucket for an easy installation, retaining your factory tank features including, the OE fuel level sending unit, EVAP system, filler neck, and if equipped with saddle style tanks, the fuel transfer pump functionality. Snow fuel hats feature female 10AN ORB feed and 8AN ORB return ports. 90 degree swivel adapter fittings are sold separately to adapt to your desired combination of 10AN, 8AN or 6AN lines. To meet your specific vehicle's fuel demands, these pump assemblies are configurable with a combination of 2 or 3 fuel pumps. No knock-off pumps here. Get OE reliability with genuine TI Automotive (Walbro) fuel pumps in your choice of flow rates (450LPH or 470LPH).These fuel pumps are designed for a return-style installation only. Do not attempt to run these pumps in a returnless application. These pumps are compatible with 100% Gasoline, 100% Ethanol or any blend of Gasoline and Ethanol (E10, E85, E98 for example). These pumps are NOT compatible with methanol.