Close ×
Choose your Vehicle
Select your vehicle for a custom shopping experience
H&R 60mm ID Single Race Spring Length 100mm Spring Rate 220 N/mm or 1256 lbs/inch
$81.86
$89.95
H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.
H&R 60mm ID Single Race Spring Length 100mm Spring Rate 240 N/mm or 1370 lbs/inch
$81.86
$89.95
H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.
H&R 60mm ID Single Race Spring Length 100mm Spring Rate 250 N/mm or 1429 lbs/inch
$81.86
$89.95
H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.
H&R 60mm ID Single Race Spring Length 100mm Spring Rate 260 N/mm or 1484 lbs/inch
$81.86
$89.95
H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.
H&R 60mm ID Single Race Spring Length 100mm Spring Rate 280 N/mm or 1598 lbs/inch
$81.86
$89.95
H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.
H&R 60mm ID Single Race Spring Length 100mm Spring Rate 300 N/mm or 1712 lbs/inch
$81.86
$89.95
H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.
H&R 60mm ID Single Race Spring Length 100mm Spring Rate 320 N/mm or 1826 lbs/inch
$81.86
$89.95
H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.
H&R 60mm ID Single Race Spring Length 100mm Spring Rate 340 N/mm or 1941 lbs/inch
$81.86
$89.95
H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.
H&R 60mm ID Single Race Spring Length 100mm Spring Rate 35 N/mm or 200 lbs/inch
$59.15
$65.00
H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.
H&R 60mm ID Single Race Spring Length 100mm Spring Rate 360 N/mm or 2055 lbs/inch
$81.86
$89.95
H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.
H&R 60mm ID Single Race Spring Length 100mm Spring Rate 380 N/mm or 2169 lbs/inch
$81.86
$89.95
H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.
H&R 60mm ID Single Race Spring Length 100mm Spring Rate 400 N/mm or 2283 lbs/inch
$81.86
$89.95
H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.
H&R 60mm ID Single Race Spring Length 100mm Spring Rate 50 N/mm or 286 lbs/inch
$59.15
$65.00
H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.
H&R 60mm ID Single Race Spring Length 100mm Spring Rate 570 N/mm or 3255 lbs/inch
$81.86
$89.95
H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.
H&R 60mm ID Single Race Spring Length 100mm Spring Rate 60 N/mm or 343 lbs/inch
$81.86
$89.95
H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.
H&R 60mm ID Single Race Spring Length 100mm Spring Rate 620 N/mm or 3543 lbs/inch
$81.86
$89.95
H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.
H&R 60mm ID Single Race Spring Length 100mm Spring Rate 650 N/mm or 3711 lbs/inch
$81.86
$89.95
H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.
H&R 60mm ID Single Race Spring Length 100mm Spring Rate 670 N/mm or 3825 lbs/inch
$81.86
$89.95
H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.
H&R 60mm ID Single Race Spring Length 100mm Spring Rate 70 N/mm or 400 lbs/inch
$81.86
$89.95
H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.
H&R 60mm ID Single Race Spring Length 100mm Spring Rate 700 N/mm or 3996 lbs/inch
$81.86
$89.95
H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.
H&R 60mm ID Single Race Spring Length 100mm Spring Rate 80 N/mm or 457 lbs/inch
$81.86
$89.95
H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.
H&R 60mm ID Single Race Spring Length 100mm Spring Rate 90 N/mm or 514 lbs/inch
$59.15
$65.00
H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.
H&R 60mm ID Single Race Spring Length 100mm Spring Rate 90 N/mm or 514 lbs/inch
$81.86
$89.95
H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.
H&R 60mm ID Single Race Spring Length 105mm Spring Rate 25 N/mm or 143 lbs/inch
$59.15
$65.00
H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.
H&R 60mm ID Single Race Spring Length 105mm Spring Rate 40 N/mm or 228 lbs/inch
$59.15
$65.00
H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.
H&R 60mm ID Single Race Spring Length 120mm Spring Rate 100 N/mm or 571 lbs/inch
$81.86
$89.95
H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.
H&R 60mm ID Single Race Spring Length 120mm Spring Rate 110 N/mm or 628 lbs/inch
$81.86
$89.95
H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.
H&R 60mm ID Single Race Spring Length 120mm Spring Rate 120 N/mm or 685 lbs/inch
$81.86
$89.95
H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.
H&R 60mm ID Single Race Spring Length 120mm Spring Rate 130 N/mm or 742 lbs/inch
$81.86
$89.95
H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.
H&R 60mm ID Single Race Spring Length 120mm Spring Rate 140 N/mm or 799 lbs/inch
$81.86
$89.95
H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.
H&R 60mm ID Single Race Spring Length 120mm Spring Rate 160 N/mm or 913 lbs/inch
$81.86
$89.95
H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.
H&R 60mm ID Single Race Spring Length 120mm Spring Rate 180 N/mm or 1027 lbs/inch
$81.86
$89.95
H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.
H&R 60mm ID Single Race Spring Length 120mm Spring Rate 200 N/mm or 1142 lbs/inch
$81.86
$89.95
H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.
H&R 60mm ID Single Race Spring Length 120mm Spring Rate 220 N/mm or 1256 lbs/inch
$81.86
$89.95
H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.
H&R 60mm ID Single Race Spring Length 120mm Spring Rate 240 N/mm or 1370 lbs/inch
$81.86
$89.95
H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.
H&R 60mm ID Single Race Spring Length 120mm Spring Rate 260 N/mm or 1484 lbs/inch
$81.86
$89.95
H&R 2.50" I.D. Race Springs are made with extremely high tensile strength wire alloy which allows the use of a thinner wire. Manufactured using advanced materials and precision technology in Germany, H&R 2.50" I.D. Race Springs are crafted from special lightweight (hf) 54SiCr6 spring steel. For any given spring rate, they are on average 15% lighter and have 10% more travel than competitors' springs. Main springs range from 6" to 18" in length and are available in a wide selection of spring rates. TENDER SPRINGS: H&R 2.50" I.D. Tender Springs are made of trapezoidal (flat rather than round) spring wire and have a low block height for maximum travel. These springs are designed for demanding motorsport environments, and like all H&R springs, have been pre-blocked at the factory so they will never set or sag. The H&R 60mm I.D. Race Spring line is crafted from special lightweight (hf) 54SiCr6 spring steel and is the most comprehensive 60mm I.D. Race Program in the U.S. If you own a Porsche GT3 or another Euro spec car, our range of 60mm I.D. Race Springs has you covered. With hundreds of main springs and tender springs available, H&R has the lengths and rates necessary for optimal tuning and setup. The H&R complete line of 60mm I.D. main springs range from 80mm to 300mm (25.4mm = 1 inch) in length and 25 N to 700 N (N/mm x 5.709 = pounds/inch) spring rates.